1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
ON/OFF/TONE fixed or doomed?
TA Forbes
Deviate Emeritus
*****
Posts: 2,353
Threads: 92
Joined: May 2010
City: Clayton, NC
#5

01-06-2013, 07:03 PM
WD is ok, but cleaners specifically made for cleaning electronic equipment are better. Try getting a hold of some Deoxit, and you will never go back to anything else.
(This post was last modified: 01-06-2013, 07:28 PM by TA Forbes.)
Find
« Next Oldest | Next Newest »


Messages In This Thread
ON/OFF/TONE fixed or doomed? - by DKinYORKpa - 01-06-2013, 09:24 AM
RE: ON/OFF/TONE fixed or doomed? - by Phlogiston - 01-06-2013, 12:27 PM
RE: ON/OFF/TONE fixed or doomed? - by Eric T - 01-06-2013, 06:45 PM
RE: ON/OFF/TONE fixed or doomed? - by DKinYORKpa - 01-06-2013, 07:01 PM
RE: ON/OFF/TONE fixed or doomed? - by TA Forbes - 01-06-2013, 07:03 PM
RE: ON/OFF/TONE fixed or doomed? - by Ron Ramirez - 01-06-2013, 07:20 PM
RE: ON/OFF/TONE fixed or doomed? - by Arran - 01-06-2013, 08:24 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently 4682 online users. [Complete List]
» 1 Member(s) | 4681 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration