1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Other Radios (Non-Philco)
Thread Rating:
  • 1 Vote(s) - 5 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Atwater-Kent model 46 console
Arran
Phorum Expert
*****
Posts: 4,703
Threads: 51
Joined: Sep 2008
City: Sandwick, BC, CA
#11

01-08-2013, 01:50 AM
Did you find a plate or stamp indicating who built the cabinet yet? Atwater Kent didn't have a cabinet shop, at least not at that time, so most of their standard issue cabinets were produced either by Red Lion or by Pooley. There was also a fairly large industry supplying aftermarket cabinets in the 1920s through the early 30s, and sometimes they would make cabinets specifically to fit a popular model.
Regards
Arrab
Find
« Next Oldest | Next Newest »


Messages In This Thread
Atwater-Kent model 46 console - by radiotvnut - 01-06-2013, 07:30 PM
RE: Atwater-Kent model 46 console - by TA Forbes - 01-06-2013, 07:37 PM
RE: Atwater-Kent model 46 console - by radiotvnut - 01-06-2013, 07:43 PM
RE: Atwater-Kent model 46 console - by 7estatdef - 01-06-2013, 08:06 PM
RE: Atwater-Kent model 46 console - by radiotvnut - 01-06-2013, 08:12 PM
RE: Atwater-Kent model 46 console - by Jayce - 01-06-2013, 09:47 PM
RE: Atwater-Kent model 46 console - by TA Forbes - 01-06-2013, 10:12 PM
RE: Atwater-Kent model 46 console - by radiotvnut - 01-07-2013, 02:43 PM
RE: Atwater-Kent model 46 console - by 7estatdef - 01-07-2013, 09:48 PM
RE: Atwater-Kent model 46 console - by Jayce - 01-07-2013, 11:06 PM
RE: Atwater-Kent model 46 console - by Arran - 01-08-2013, 01:50 AM
RE: Atwater-Kent model 46 console - by radiotvnut - 01-08-2013, 01:58 AM
RE: Atwater-Kent model 46 console - by Phlogiston - 01-08-2013, 03:11 AM
RE: Atwater-Kent model 46 console - by radiotvnut - 01-09-2013, 02:45 AM
RE: Atwater-Kent model 46 console - by Elijah - 01-17-2013, 01:46 PM
RE: Atwater-Kent model 46 console - by Jayce - 01-17-2013, 05:35 PM
RE: Atwater-Kent model 46 console - by radiotvnut - 01-17-2013, 05:42 PM
RE: Atwater-Kent model 46 console - by Jayce - 01-17-2013, 06:26 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM
IF can wire size and Rubber mounts?
A pair of wire strippers can give you an idea of what the existing gauge of the wire leads are in the IF can, I think it...Arran — 06:07 AM
My last cabinet for this year
Hello Dan, That is really beautiful what great looking radio you have ! I have friends who live in Calgary and the wea...radiorich — 01:51 AM

[-]
Who's Online
There are currently 4493 online users. [Complete List]
» 3 Member(s) | 4490 Guest(s)
AvatarAvatarAvatar

>
  1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Other Radios (Non-Philco)