41-220 Capacitor

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

41-220 Capacitor

Jim Dutridge
Senior Member

Posts: 290
Threads: 54
Joined: Mar 2007
City: Toledo State, Province, Country: OH

01-09-2013, 05:21 PM

Got everything back together and want to check the alignment. Where is the AVC line in this radio? Off the bottom side of of the 2.2M resistor #27 or the 4.7M resistor #34?

Find

« Next Oldest | Next Newest »

Messages In This Thread

41-220 Capacitor - by Jim Dutridge - 01-02-2013, 06:10 PM

RE: 41-220 Capacitor - by Ron Ramirez - 01-03-2013, 04:46 PM

RE: 41-220 Capacitor - by Jim Dutridge - 01-03-2013, 05:10 PM

RE: 41-220 Capacitor - by Ron Ramirez - 01-03-2013, 05:16 PM

RE: 41-220 Capacitor - by codefox1 - 01-03-2013, 11:37 PM

RE: 41-220 Capacitor - by Jim Dutridge - 01-05-2013, 11:51 AM

RE: 41-220 Capacitor - by exray - 01-06-2013, 07:37 AM

RE: 41-220 Capacitor - by codefox1 - 01-06-2013, 04:57 PM

RE: 41-220 Capacitor - by Jim Dutridge - 01-09-2013, 05:21 PM

RE: 41-220 Capacitor - by Ron Ramirez - 01-09-2013, 07:19 PM

RE: 41-220 Capacitor - by Jim Dutridge - 01-10-2013, 04:22 PM

RE: 41-220 Capacitor - by Ron Ramirez - 01-10-2013, 06:49 PM

RE: 41-220 Capacitor - by Jim Dutridge - 01-10-2013, 09:15 PM

RE: 41-220 Capacitor - by Jim Dutridge - 01-13-2013, 01:42 PM

RE: 41-220 Capacitor - by Jim Dutridge - 01-17-2013, 09:13 PM

RE: 41-220 Capacitor - by Arran - 01-17-2013, 10:39 PM

RE: 41-220 Capacitor - by Jim Dutridge - 01-18-2013, 06:24 PM

RE: 41-220 Capacitor - by Jim Dutridge - 01-19-2013, 10:59 PM

View a Printable Version

Users browsing this thread: 2 Guest(s)

Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

Who's Online

There are currently 4642 online users. [Complete List]
» 1 Member(s) | 4641 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me