Still Not Tracking Right

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Still Not Tracking Right

Elijah
Member

Posts: 65
Threads: 12
Joined: Dec 2012
City: TN

01-09-2013, 09:22 PM

That's what I did, Ron. I adjusted after I tightened A3. I did that first thing. The instructions for the low end was to use a .1mfd cap to the B- side and high side of generator to pin 6 of 7A8 with the generator on 455 and tuning cap fully closed. That was it on the low end. I may go back and try again. I moved the radio to another area and reception/volume was better but the stations are still off by about 50KHz.

Find

« Next Oldest | Next Newest »

Messages In This Thread

Still Not Tracking Right - by Elijah - 01-08-2013, 08:50 PM

RE: Still Not Tracking Right - by BrendaAnnD - 01-08-2013, 11:50 PM

RE: Still Not Tracking Right - by Elijah - 01-09-2013, 05:01 PM

RE: Still Not Tracking Right - by Ron Ramirez - 01-09-2013, 07:28 PM

RE: Still Not Tracking Right - by Elijah - 01-09-2013, 09:22 PM

RE: Still Not Tracking Right - by dixierat - 01-09-2013, 09:58 PM

RE: Still Not Tracking Right - by Elijah - 01-09-2013, 11:26 PM

RE: Still Not Tracking Right - by TA Forbes - 01-09-2013, 11:34 PM

RE: Still Not Tracking Right - by dixierat - 01-10-2013, 10:59 AM

RE: Still Not Tracking Right - by Ron Ramirez - 01-10-2013, 11:21 AM

RE: Still Not Tracking Right - by BrendaAnnD - 01-10-2013, 09:55 PM

RE: Still Not Tracking Right - by TA Forbes - 01-10-2013, 11:50 PM

RE: Still Not Tracking Right - by Elijah - 01-11-2013, 11:37 AM

RE: Still Not Tracking Right - by TA Forbes - 01-11-2013, 02:38 PM

RE: Still Not Tracking Right - by Ron Ramirez - 01-11-2013, 02:43 PM

RE: Still Not Tracking Right - by codefox1 - 01-12-2013, 03:59 PM

RE: Still Not Tracking Right - by Elijah - 01-12-2013, 08:03 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

Who's Online

There are currently 4907 online users. [Complete List]
» 2 Member(s) | 4905 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me