1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Production changes: 16B
Chuck Schwark
Phorum Expert
*****
Posts: 1,703
Threads: 55
Joined: Sep 2005
City: Evanston, IL
#5

01-09-2013, 10:35 PM
Brenda,

You will get all pertinent Model 16 Philco Production Change Notes with the info packet you ordered.

Could you please list the tube complement of your set, so I can narrow down the probable Code version of your set?

The Model 16 went through at least eight Code version revisions and many, many Run numbers (minor component changes) within those major Code versions. Want to sent the most accurate info I can for you. Riders usually never can give you the correct info, as they did not always re-publish subsequent changes or revisions from the manufacturers, as I have found out for Philco lit from that source.

Thanks,

Chuck :-)
Chuck Schwark,
The Philco Repair Bench
[Image: http://www.philcorepairbench.com/images/philog3tiny.gif]
http://www.philcorepairbench.com
Website Find
« Next Oldest | Next Newest »


Messages In This Thread
Production changes: 16B - by BrendaAnnD - 01-08-2013, 09:54 AM
RE: Production changes: 16B - by Ron Ramirez - 01-09-2013, 01:34 PM
RE: Production changes: 16B - by BrendaAnnD - 01-09-2013, 05:28 PM
RE: Production changes: 16B - by Ron Ramirez - 01-09-2013, 07:13 PM
RE: Production changes: 16B - by Chuck Schwark - 01-09-2013, 10:35 PM
RE: Production changes: 16B - by TA Forbes - 01-09-2013, 11:30 PM
RE: Production changes: 16B - by BrendaAnnD - 01-10-2013, 02:02 AM
RE: Production changes: 16B - by TA Forbes - 01-10-2013, 10:12 AM
RE: Production changes: 16B - by Ron Ramirez - 01-10-2013, 10:16 AM
RE: Production changes: 16B - by BrendaAnnD - 01-10-2013, 08:18 PM
RE: Production changes: 16B - by Ron Ramirez - 01-10-2013, 08:31 PM
RE: Production changes: 16B - by BrendaAnnD - 01-10-2013, 08:44 PM
RE: Production changes: 16B - by BrendaAnnD - 01-11-2013, 09:51 AM
RE: Production changes: 16B - by TA Forbes - 01-11-2013, 02:46 PM
RE: Production changes: 16B - by BrendaAnnD - 01-16-2013, 10:02 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration