1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Production changes: 16B
BrendaAnnD
Phorum Expert
*****
Posts: 1,108
Threads: 89
Joined: Jun 2011
City: Tacoma State, Province, Country: Washington
#7

01-10-2013, 02:02 AM
Ron,

The one on the schematic and parts layout that I cannot find is 18.

Chuck,

The tube compliment is as follows:

Rect. 80 (schem. I have shows 5-Z-3, but I think even the socket shows 80 on this set)
Outputs. 2 x 42
Driver. 42
Osc. 76
1st Det./Mixer 77
1st IF and 2nd IF. 78
2nd Det. 37
1st AF. 77
QAVC. 78
Find
« Next Oldest | Next Newest »


Messages In This Thread
Production changes: 16B - by BrendaAnnD - 01-08-2013, 09:54 AM
RE: Production changes: 16B - by Ron Ramirez - 01-09-2013, 01:34 PM
RE: Production changes: 16B - by BrendaAnnD - 01-09-2013, 05:28 PM
RE: Production changes: 16B - by Ron Ramirez - 01-09-2013, 07:13 PM
RE: Production changes: 16B - by Chuck Schwark - 01-09-2013, 10:35 PM
RE: Production changes: 16B - by TA Forbes - 01-09-2013, 11:30 PM
RE: Production changes: 16B - by BrendaAnnD - 01-10-2013, 02:02 AM
RE: Production changes: 16B - by TA Forbes - 01-10-2013, 10:12 AM
RE: Production changes: 16B - by Ron Ramirez - 01-10-2013, 10:16 AM
RE: Production changes: 16B - by BrendaAnnD - 01-10-2013, 08:18 PM
RE: Production changes: 16B - by Ron Ramirez - 01-10-2013, 08:31 PM
RE: Production changes: 16B - by BrendaAnnD - 01-10-2013, 08:44 PM
RE: Production changes: 16B - by BrendaAnnD - 01-11-2013, 09:51 AM
RE: Production changes: 16B - by TA Forbes - 01-11-2013, 02:46 PM
RE: Production changes: 16B - by BrendaAnnD - 01-16-2013, 10:02 AM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently 4855 online users. [Complete List]
» 1 Member(s) | 4854 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration