1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco 18 changes
DKinYORKpa
Member
***
Posts: 193
Threads: 50
Joined: Oct 2011
City: York PA
#8

01-10-2013, 08:40 PM
Quote:Because it did not exist until I created it in Paint Shop Pro, to try and help you out

Icon_evilIcon_lol You know I just went out to my shop and took a closer look and you are absolutely right! The piece of sheet metal on the top of the chassis that was folded up straight in the air for those cans is neatly sawed off! This was to make a little room for the Solar can to be attached and screwed to the chassis. How could I have ever doubted you Icon_redface ?
Find
« Next Oldest | Next Newest »


Messages In This Thread
Philco 18 changes - by DKinYORKpa - 01-09-2013, 01:15 PM
RE: Philco 18 changes - by DKinYORKpa - 01-10-2013, 08:40 AM
RE: Philco 18 changes - by Ron Ramirez - 01-10-2013, 08:45 AM
RE: Philco 18 changes - by DKinYORKpa - 01-10-2013, 06:14 PM
RE: Philco 18 changes - by Ron Ramirez - 01-10-2013, 07:55 PM
RE: Philco 18 changes - by DKinYORKpa - 01-10-2013, 08:23 PM
RE: Philco 18 changes - by Ron Ramirez - 01-10-2013, 08:27 PM
RE: Philco 18 changes - by DKinYORKpa - 01-10-2013, 08:40 PM
RE: Philco 18 changes - by Ron Ramirez - 01-10-2013, 08:58 PM
RE: Philco 18 changes - by TA Forbes - 01-10-2013, 11:54 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently 4616 online users. [Complete List]
» 1 Member(s) | 4615 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration