1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Still Not Tracking Right
BrendaAnnD
Phorum Expert
*****
Posts: 1,108
Threads: 89
Joined: Jun 2011
City: Tacoma State, Province, Country: Washington
#11

01-10-2013, 09:55 PM
I didn't even consider that the sig gen may be off calibration, since I use PLL sig gens.. that could give a large error in the IF and corresponding mistracking on the dial.
Find
« Next Oldest | Next Newest »


Messages In This Thread
Still Not Tracking Right - by Elijah - 01-08-2013, 08:50 PM
RE: Still Not Tracking Right - by BrendaAnnD - 01-08-2013, 11:50 PM
RE: Still Not Tracking Right - by Elijah - 01-09-2013, 05:01 PM
RE: Still Not Tracking Right - by Ron Ramirez - 01-09-2013, 07:28 PM
RE: Still Not Tracking Right - by Elijah - 01-09-2013, 09:22 PM
RE: Still Not Tracking Right - by dixierat - 01-09-2013, 09:58 PM
RE: Still Not Tracking Right - by Elijah - 01-09-2013, 11:26 PM
RE: Still Not Tracking Right - by TA Forbes - 01-09-2013, 11:34 PM
RE: Still Not Tracking Right - by dixierat - 01-10-2013, 10:59 AM
RE: Still Not Tracking Right - by Ron Ramirez - 01-10-2013, 11:21 AM
RE: Still Not Tracking Right - by BrendaAnnD - 01-10-2013, 09:55 PM
RE: Still Not Tracking Right - by TA Forbes - 01-10-2013, 11:50 PM
RE: Still Not Tracking Right - by Elijah - 01-11-2013, 11:37 AM
RE: Still Not Tracking Right - by TA Forbes - 01-11-2013, 02:38 PM
RE: Still Not Tracking Right - by Ron Ramirez - 01-11-2013, 02:43 PM
RE: Still Not Tracking Right - by codefox1 - 01-12-2013, 03:59 PM
RE: Still Not Tracking Right - by Elijah - 01-12-2013, 08:03 PM



Users browsing this thread: 3 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently 4799 online users. [Complete List]
» 1 Member(s) | 4798 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration