Atwater-Kent 72

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Atwater-Kent 72

Jayce
Phorum Expert

Posts: 2,023
Threads: 365
Joined: Jun 2010
City: Dover, OH

01-10-2013, 10:39 PM

Well, I will keep my fingers crossed. I pulled up the print and the 72 is indeed a Superheterodyne and there were two chassis versions, H1 and H2. I will have to check the serial on mine to see which one it is. I was looking at a model 74 table that was right beside this radio and it looked the same, but I think the chassis in it was TRF. Odd, because to look at the two, you can't really tell the difference other than mine having 'Superheterodyne' proudly stamped on it. If all goes right, this looks like it should be a good performer.

No matter where you go, there you are.

Find

« Next Oldest | Next Newest »

Messages In This Thread

Atwater-Kent 72 - by Jayce - 01-10-2013, 03:24 PM

RE: Atwater-Kent 72 - by Ron Ramirez - 01-10-2013, 03:53 PM

RE: Atwater-Kent 72 - by TA Forbes - 01-10-2013, 03:59 PM

RE: Atwater-Kent 72 - by Jayce - 01-10-2013, 04:24 PM

RE: Atwater-Kent 72 - by Phlogiston - 01-10-2013, 05:22 PM

RE: Atwater-Kent 72 - by Ron Ramirez - 01-10-2013, 05:51 PM

RE: Atwater-Kent 72 - by Arran - 01-10-2013, 09:21 PM

RE: Atwater-Kent 72 - by Jayce - 01-10-2013, 10:39 PM

RE: Atwater-Kent 72 - by TA Forbes - 01-10-2013, 11:04 PM

RE: Atwater-Kent 72 - by radiotvnut - 01-11-2013, 02:14 AM

View a Printable Version

Users browsing this thread: 2 Guest(s)

Recent Posts
Bakelite crack repair - what is best epoxy?
Thanks everyone. I appreciate you sharing your experience and looks like I'll work with the 24 hr two part clear epoxy....de371 — 10:25 PM
Jackson 665 j2 schematic request
Without a schematic its going to be hard tracing the wire wound spool resistors.daveone23 — 05:21 PM
Jackson 665 j2 schematic request
Looking for a schematic for the 665 j2 multimeter.daveone23 — 04:42 PM
Looking for place to donate unique Philco Philco J-1930 Prototype
>>I'll write to the Henry Ford. I heard, his secretary answers his mail, not he himself.morzh — 12:15 PM
Philco 48-200 alignment questions
Just checked the power cord and I did in fact wire it so the hot side (small prong) goes to the switch.transitony — 11:52 AM
Looking for place to donate unique Philco Philco J-1930 Prototype
Thanks for the suggestions. I'll write to the Henry Ford. That would certainly make sense since by the time this prod...jeibner — 11:49 AM
Looking for place to donate unique Philco Philco J-1930 Prototype
For what it's worth, the Henry Ford Museum and Greenfield Village in Dearborn, Michigan may be an option. The obvious ...GarySP — 11:39 AM
Help with Readrite 410 tube tester
Mike and I just had a short discussion yesterday about this very subject. So often it's the connections. Ya gotta have t...RodB — 10:08 AM
Looking for place to donate unique Philco Philco J-1930 Prototype
We have a regional museum here in the Twin Cities called The Pavek Museum. They have an extensive collection of communic...RodB — 09:30 AM
Philco 89B code 123 newbie
I did some nosing around and found that the original caps were 4 3/4" long x 1 5/16" in dia. Guess what 1"...Radioroslyn — 09:28 AM

Who's Online

There are currently 4499 online users. [Complete List]
» 3 Member(s) | 4496 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me