1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Let's see your radio workbench!
murf
Senior Member
****
Posts: 668
Threads: 144
Joined: Jun 2011
City: Elko,MN.
#2

01-14-2013, 04:00 PM
I went high tech with mine.
I use a card table with a soldering iron sitting in one corner.
Clamp on light in the other corner.
Toolbox sitting on the floor underneath.
Radios lined up on all 4 walls.
How's that for a man cave.
murf
Find
« Next Oldest | Next Newest »


Messages In This Thread
Let's see your radio workbench! - by Conelrad - 01-14-2013, 02:39 PM
RE: Let's see your radio workbench! - by murf - 01-14-2013, 04:00 PM
RE: Let's see your radio workbench! - by y2kbruce - 01-14-2013, 07:18 PM
RE: Let's see your radio workbench! - by shawn - 01-15-2013, 06:31 PM
RE: Let's see your radio workbench! - by y2kbruce - 01-16-2013, 08:22 PM
RE: Let's see your radio workbench! - by Arran - 01-16-2013, 08:59 PM
RE: Let's see your radio workbench! - by Dave - 01-17-2013, 06:34 PM



Users browsing this thread: 3 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently 4860 online users. [Complete List]
» 1 Member(s) | 4859 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration