1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
New Philco 20 Filter Caps...In, but Another Question??
Joe
Junior Member
**
Posts: 31
Threads: 5
Joined: Feb 2012
#15

01-16-2013, 09:00 PM
Thanks, it just made some sort of sense to use the chassis as a heat sink. BUT, do you think that 10 watts is enough to replace the 1400 ohm wire wound resistor? . It gets too hot to touch.
Find
« Next Oldest | Next Newest »


Messages In This Thread
RE: Philco 20 Dead - by Elijah - 01-02-2013, 10:14 PM
RE: Philco 20 Dead - by TA Forbes - 01-02-2013, 10:28 PM
RE: Philco 20 Dead - by Joe - 01-02-2013, 11:41 PM
Philco 20 Voltages?? - by Joe - 01-13-2013, 06:31 PM
RE: Philco 20 Voltages - by Ron Ramirez - 01-13-2013, 07:19 PM
RE: Philco 20 Voltages - by Joe - 01-13-2013, 07:37 PM
RE: Philco 20 Voltages - by Ron Ramirez - 01-13-2013, 08:07 PM
RE: Philco 20 Voltages - by Joe - 01-13-2013, 08:17 PM
RE: Philco 20 Voltages - by Ron Ramirez - 01-13-2013, 08:23 PM
RE: Philco 20 Voltages - by Joe - 01-13-2013, 08:31 PM
RE: Philco 20 Voltages - by Ron Ramirez - 01-14-2013, 06:35 AM
RE: Philco 20 Voltages - by Joe - 01-16-2013, 03:00 PM
RE: Philco 20 Voltages - by codefox1 - 01-16-2013, 07:05 PM
RE: Philco 20 Voltages - by Joe - 01-16-2013, 09:00 PM
RE: Philco 20 Voltages - by TA Forbes - 01-16-2013, 09:59 PM
RE: Philco 20 Voltages - by Joe - 01-16-2013, 10:47 PM
RE: Philco 20 Voltages - by TA Forbes - 01-16-2013, 11:27 PM
RE: Philco 20 Voltages - by Joe - 01-17-2013, 12:10 AM
RE: Philco 20 Voltages - by 7estatdef - 01-17-2013, 06:16 PM
RE: Philco 20 Voltages - by Joe - 01-18-2013, 12:46 PM
RE: Philco 20 Filter Caps?? - by codefox1 - 01-18-2013, 09:02 PM
RE: Philco 20 Filter Caps?? - by Ron Ramirez - 01-18-2013, 09:38 PM
RE: Philco 20 Filter Caps?? - by Joe - 01-19-2013, 12:28 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently 4664 online users. [Complete List]
» 1 Member(s) | 4663 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration