1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Candohm replacement
klondike98
Phorum Moderator
******
Posts: 5,160
Threads: 273
Joined: Nov 2012
City: Wilsonville State, Province, Country: OR
#10

01-17-2013, 12:50 PM
Thanks BrendaAnnD.

a) 35Z3 cathode is -1vDC
b) 35Z3 plate is 108vAC (line is 110vAC through isolation xfmr)
c) both in and out of field coil are -1vDC
d) B- common is same wire as original wire (but heat shrink covered to replace old rubber) and has continuity to other B- points
e) dial lamp is working (now that candohm was replaced with some power resistors http://philcoradio.com/phorum/showthread.php?tid=5697 )

Regards,
bob
Cheers,
Bob
[Image: https://www.dropbox.com/s/5m63ib99yfx2eg....jpg?raw=1]
Bob's Restorations Web Page
Website Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
Candohm replacement - by klondike98 - 01-05-2013, 04:33 PM
RE: Candohm replacement - by codefox1 - 01-05-2013, 05:04 PM
RE: Candohm replacement - by morzh - 01-05-2013, 06:10 PM
RE: Candohm replacement - by klondike98 - 01-05-2013, 06:39 PM
RE: Candohm replacement - by Arran - 01-05-2013, 10:35 PM
RE: Candohm replacement - by Phlogiston - 01-05-2013, 11:26 PM
RE: Candohm replacement - by klondike98 - 01-06-2013, 02:57 PM
RE: Electrolytic cap polarity question/advice - by klondike98 - 01-17-2013, 12:50 PM



Users browsing this thread:
[-]
Recent Posts
Philco 610B oscillator wiring
Some info from Beitmans says late production. David   David — 06:06 PM
Restoring Philco 96
Oh wow! Just found this thread.  Brings me back to early days on this phorum.  I did a 96 back in 2017.  Thread here: ...rfeenstra — 06:05 PM
Philco 610B oscillator wiring
Thanks for the replies. It's not the really the hum that I am after. Just trying to understand why only the shortwave ba...Tubester — 04:01 PM
Restoring Philco 96
70 and 90 are Superhets, but at least the 2x45 model of 90 uses the Plate detector (and so does 70). Also the Atwaters,...morzh — 03:28 PM
Restoring Philco 96
Morzh, Prayers for your mom. I am sure that there was enough pain living through the Holocaust as a child. I pray dail...MrFixr55 — 02:19 PM
Philco 610B oscillator wiring
Hi Dan, Divide and conquer. First off trry to differentiate between 60Hz and 120 Hz hum. 120 Hz hum has a higher pit...MrFixr55 — 01:49 PM
Restoring Philco 96
Yes, other than takin a toll on your back, they are undeed way more repair friendly than many other Philcos. To me, som...morzh — 01:04 PM
Philco 610B oscillator wiring
If the wires look like they were this way from the factory (very neat and very dull soldering joints), I'd leave them be...morzh — 12:58 PM
My Philco 37-116 Restore
I managed to open up the Expander Unit and replace the grid cap wires. Tested the connections found they looked good and...dconant — 12:19 PM
610B Oscillator Questions
I've included a picture of the 'actual' schematic I created. I double checked several times and it appears to be accur...Tubester — 09:26 AM

[-]
Who's Online
There are currently 2431 online users. [Complete List]
» 2 Member(s) | 2429 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration