Late Model 60 sensitivity/bandwith when tuning

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Late Model 60 sensitivity/bandwith when tuning

SteveJB
Member

Posts: 236
Threads: 43
Joined: Oct 2010
City: Atlantic Highlands, NJ

#11

01-19-2013, 11:06 PM

The alignment instructions in Riders dont say where to inject the signal. I did try the grid of the 6A7 also but may not have done something right as I didnt see any change.

Find

« Next Oldest | Next Newest »

Messages In This Thread

Late Model 60 sensitivity/bandwith when tuning - by SteveJB - 01-18-2013, 09:09 PM

RE: Late Model 60 sensitivity/bandwith when tuning - by TA Forbes - 01-18-2013, 09:41 PM

RE: Late Model 60 sensitivity/bandwith when tuning - by SteveJB - 01-18-2013, 09:46 PM

RE: Late Model 60 sensitivity/bandwith when tuning - by TA Forbes - 01-18-2013, 09:47 PM

RE: Late Model 60 sensitivity/bandwith when tuning - by SteveJB - 01-18-2013, 09:52 PM

RE: Late Model 60 sensitivity/bandwith when tuning - by SteveJB - 01-18-2013, 09:57 PM

RE: Late Model 60 sensitivity/bandwith when tuning - by TA Forbes - 01-19-2013, 02:16 PM

RE: Late Model 60 sensitivity/bandwith when tuning - by codefox1 - 01-19-2013, 03:57 PM

RE: Late Model 60 sensitivity/bandwith when tuning - by SteveJB - 01-19-2013, 09:19 PM

RE: Late Model 60 sensitivity/bandwith when tuning - by TA Forbes - 01-19-2013, 10:41 PM

RE: Late Model 60 sensitivity/bandwith when tuning - by SteveJB - 01-19-2013, 11:06 PM

RE: Late Model 60 sensitivity/bandwith when tuning - by Ron Ramirez - 01-20-2013, 11:56 AM

RE: Late Model 60 sensitivity/bandwith when tuning - by SteveJB - 01-20-2013, 01:01 PM

RE: Late Model 60 sensitivity/bandwith when tuning - by SteveJB - 01-20-2013, 09:34 PM

RE: Late Model 60 sensitivity/bandwith when tuning - by jack_17 - 03-10-2013, 09:55 PM

RE: Late Model 60 sensitivity/bandwith when tuning - by Ron Ramirez - 03-11-2013, 05:33 AM

RE: Late Model 60 sensitivity/bandwith when tuning - by Lewiss - 01-25-2022, 11:53 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM

Who's Online

There are currently 5304 online users. [Complete List]
» 1 Member(s) | 5303 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me