Zenith Model K725

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Zenith Model K725

Ron Ramirez
Silent Key

Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand State, Province, Country: Indiana

#14

01-20-2013, 11:05 AM

Finally, a picture of the tool you need...

[Image: http://i326.photobucket.com/albums/k420/...extool.jpg]

Notice how the hex end is larger than the neck of the tool? This allows the tool to go down through the top slug to the bottom slug so that it may be adjusted without changing the adjustment of the top slug.

I took the picture from an eBay ad, with apologies to this seller who I hope won't mind if I link to his ad:
http://cgi.ebay.com/230915212377

--
Ron Ramirez
Ferdinand IN

Find

« Next Oldest | Next Newest »

Messages In This Thread

Zenith Model K725 - by Elijah - 01-16-2013, 07:42 PM

RE: Zenith Model K725 - by Glenn Roberts - 01-16-2013, 07:45 PM

RE: Zenith Model K725 - by Elijah - 01-16-2013, 07:48 PM

RE: Zenith Model K725 - by exray - 01-16-2013, 08:32 PM

RE: Zenith Model K725 - by Elijah - 01-16-2013, 08:44 PM

RE: Zenith Model K725 - by Ron Ramirez - 01-17-2013, 08:28 AM

RE: Zenith Model K725 - by Glenn Roberts - 01-17-2013, 08:46 AM

RE: Zenith Model K725 - by Ron Ramirez - 01-17-2013, 09:08 AM

RE: Zenith Model K725 - by Elijah - 01-17-2013, 11:49 AM

RE: Zenith Model K725 - by Glenn Roberts - 01-18-2013, 01:59 PM

RE: Zenith Model K725 - by Elijah - 01-18-2013, 03:20 PM

RE: Zenith Model K725 - by Arran - 01-18-2013, 08:43 PM

RE: Zenith Model K725 - by Elijah - 01-19-2013, 11:54 PM

RE: Zenith Model K725 - by Ron Ramirez - 01-20-2013, 11:05 AM

RE: Zenith Model K725 - by Elijah - 01-21-2013, 05:58 PM

RE: Zenith Model K725 - by Elijah - 01-22-2013, 07:43 PM

RE: Zenith Model K725 - by Elijah - 01-23-2013, 11:23 AM

RE: Zenith Model K725 - by Elijah - 02-02-2013, 02:46 PM

View a Printable Version

Users browsing this thread: 4 Guest(s)

Recent Posts
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM
IF can wire size and Rubber mounts?
A pair of wire strippers can give you an idea of what the existing gauge of the wire leads are in the IF can, I think it...Arran — 06:07 AM
My last cabinet for this year
Hello Dan, That is really beautiful what great looking radio you have ! I have friends who live in Calgary and the wea...radiorich — 01:51 AM

Who's Online

There are currently 4535 online users. [Complete List]
» 2 Member(s) | 4533 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me