Starting a 66B

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Starting a 66B

Jim Dutridge
Senior Member

Posts: 290
Threads: 54
Joined: Mar 2007
City: Toledo State, Province, Country: OH

01-20-2013, 10:43 PM

Now that I have my 41-220 working I am going to start a rebuild on a 66B tombstone and was curious if there were any pitfalls to watch out for? A good start is that the IFs and coils check good. Bad thing is the choke shows open. Also, the speaker cone is pretty well tore up so will need a new cone for it.

(This post was last modified: 01-20-2013, 10:58 PM by Jim Dutridge.)

Find

« Next Oldest | Next Newest »

Messages In This Thread

Starting a 66B - by Jim Dutridge - 01-20-2013, 10:43 PM

RE: Starting a 66B - by jph14 - 01-22-2013, 09:07 AM

RE: Starting a 66B - by Jim Dutridge - 01-23-2013, 02:51 PM

RE: Starting a 66B - by Jim Dutridge - 01-23-2013, 06:06 PM

RE: Starting a 66B - by Jim Dutridge - 01-23-2013, 06:14 PM

RE: Starting a 66B - by Jim Dutridge - 01-24-2013, 05:57 PM

RE: Starting a 66B - by Steve Davis - 01-24-2013, 06:45 PM

RE: Starting a 66B - by Ron Ramirez - 01-24-2013, 06:58 PM

RE: Starting a 66B - by jph14 - 01-25-2013, 08:08 AM

View a Printable Version

Users browsing this thread: 2 Guest(s)

Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

Who's Online

There are currently 4826 online users. [Complete List]
» 1 Member(s) | 4825 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me