1936? model 84 resistor

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

1936? model 84 resistor

brownie45
Member

Posts: 54
Threads: 8
Joined: Nov 2012
City: Wilton, Iowa

01-22-2013, 09:10 PM

Thanks for the info.
Is the 4 meg. resistor mounted in the IF transformer pretty reliable or
should it be checked also? Hate to get into the IF if not needed.
How much of an antenna should this unit have? I'm assuming a
good ground is mandatory.
Is the 2 section electrolytic filter re-stuffable, or do you just put
new singles under the chassis? The filter looks rather hard to re-stuff.
Thanks again. Jim

Find

« Next Oldest | Next Newest »

Messages In This Thread

1936? model 84 resistor - by brownie45 - 01-22-2013, 03:48 PM

RE: 1936? model 84 resistor - by Ron Ramirez - 01-22-2013, 07:30 PM

RE: 1936? model 84 resistor - by brownie45 - 01-22-2013, 09:10 PM

RE: 1936? model 84 resistor - by 7estatdef - 01-26-2013, 09:30 AM

RE: 1936? model 84 resistor - by Ron Ramirez - 01-26-2013, 10:02 AM

RE: 1936? model 84 resistor - by Ron Ramirez - 01-26-2013, 10:03 AM

RE: 1936? model 84 resistor - by brownie45 - 01-26-2013, 02:50 PM

RE: 1936? model 84 resistor - by codefox1 - 01-26-2013, 03:18 PM

RE: 1936? model 84 resistor - by Ron Ramirez - 01-26-2013, 07:19 PM

RE: 1936? model 84 resistor - by brownie45 - 01-26-2013, 09:04 PM

RE: 1936? model 84 resistor - by Ron Ramirez - 01-26-2013, 09:10 PM

RE: 1936? model 84 resistor - by 7estatdef - 01-26-2013, 09:10 PM

RE: 1936? model 84 resistor - by Ron Ramirez - 01-26-2013, 09:12 PM

RE: 1936? model 84 resistor - by brownie45 - 01-26-2013, 10:41 PM

RE: 1936? model 84 resistor - by 7estatdef - 01-27-2013, 09:59 AM

RE: 1936? model 84 resistor - by brownie45 - 01-28-2013, 04:55 PM

RE: 1936? model 84 resistor - by 7estatdef - 01-28-2013, 11:48 PM

RE: 1936? model 84 resistor - by brownie45 - 01-29-2013, 07:38 AM

RE: 1936? model 84 resistor - by Ron Ramirez - 01-29-2013, 10:52 AM

RE: 1936? model 84 resistor - by brownie45 - 01-29-2013, 02:40 PM

RE: 1936? model 84 resistor - by klondike98 - 01-29-2013, 03:00 PM

RE: 1936? model 84 resistor - by Ron Ramirez - 01-29-2013, 03:16 PM

RE: 1936? model 84 resistor - by brownie45 - 01-29-2013, 03:26 PM

RE: 1936? model 84 resistor - by 7estatdef - 01-29-2013, 05:37 PM

RE: 1936? model 84 resistor - by brownie45 - 01-29-2013, 06:39 PM

RE: 1936? model 84 resistor - by 7estatdef - 01-29-2013, 08:48 PM

RE: 1936? model 84 resistor - by brownie45 - 02-01-2013, 03:49 PM

RE: 1936? model 84 resistor - by brownie45 - 02-01-2013, 04:37 PM

RE: 1936? model 84 resistor - by 7estatdef - 02-01-2013, 11:00 PM

RE: 1936? model 84 resistor - by brownie45 - 02-02-2013, 08:10 AM

RE: 1936? model 84 resistor - by 7estatdef - 02-03-2013, 10:07 PM

RE: 1936? model 84 resistor - by brownie45 - 02-04-2013, 08:01 AM

RE: 1936? model 84 resistor - by 7estatdef - 02-04-2013, 10:00 AM

RE: 1936? model 84 resistor - by brownie45 - 02-04-2013, 11:19 AM

View a Printable Version

Users browsing this thread: 3 Guest(s)

Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

Who's Online

There are currently 4864 online users. [Complete List]
» 1 Member(s) | 4863 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me