1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
philco 42-1012
TA Forbes
Deviate Emeritus
*****
Posts: 2,353
Threads: 92
Joined: May 2010
City: Clayton, NC
#8

01-25-2013, 12:44 AM
Did you place the blade of a screwdriver on the grid RF or the det/osc tube to see if it bought in the sound any better?

Also check the output transformer and the interstage transformer for continuity. The output transformers are pone to failure.
Find
« Next Oldest | Next Newest »


Messages In This Thread
philco 42-1012 - by murf - 01-06-2013, 12:21 AM
RE: philco 42-1012 - by TA Forbes - 01-06-2013, 02:41 AM
RE: philco 42-1012 - by shawn - 01-16-2013, 09:48 PM
RE: philco 42-1012 - by murf - 01-16-2013, 10:00 PM
RE: philco 42-1012 - by TA Forbes - 01-16-2013, 10:02 PM
RE: philco 42-1012 - by murf - 01-16-2013, 11:33 PM
RE: philco 42-1012 - by murf - 01-24-2013, 11:53 PM
RE: philco 42-1012 - by TA Forbes - 01-25-2013, 12:44 AM
RE: philco 42-1012 - by Arran - 01-25-2013, 03:00 AM
RE: philco 42-1012 - by murf - 01-27-2013, 06:13 PM
RE: philco 42-1012 - by Electrothaumaturgist - 01-30-2013, 04:54 PM
RE: philco 42-1012 - by Arran - 01-30-2013, 10:24 PM
RE: philco 42-1012 - by murf - 01-30-2013, 10:45 PM
RE: philco 42-1012 - by codefox1 - 01-31-2013, 02:06 PM
RE: philco 42-1012 - by murf - 01-31-2013, 06:19 PM
RE: philco 42-1012 - by Electrothaumaturgist - 01-31-2013, 09:02 PM
RE: philco 42-1012 - by murf - 01-31-2013, 09:14 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration