1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Home Radios
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco Model 610
TA Forbes
Deviate Emeritus
*****
Posts: 2,353
Threads: 92
Joined: May 2010
City: Clayton, NC
#2

01-25-2013, 11:49 PM
It's a five-tube, three band set. For what it is, it gets good reception on all bands with a good antenna.
Find
« Next Oldest | Next Newest »


Messages In This Thread
Philco Model 610 - by Eric Adams - 01-25-2013, 09:45 PM
RE: Philco Model 610 - by TA Forbes - 01-25-2013, 11:49 PM
RE: Philco Model 610 - by Eric Adams - 01-26-2013, 12:34 AM
RE: Philco Model 610 - by Arran - 01-26-2013, 01:31 AM
RE: Philco Model 610 - by Ron Ramirez - 01-26-2013, 09:14 AM
RE: Philco Model 610 - by 7estatdef - 01-31-2013, 06:46 PM
RE: Philco Model 610 - by Eric Adams - 02-01-2013, 07:07 PM
RE: Philco Model 610 - by Arran - 02-01-2013, 11:01 PM
RE: Philco Model 610 - by Eric Adams - 02-01-2013, 11:31 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Not sure if anyone has tried this but there are 6.3 volt miniature lamps in bayonet and screw-in base options available ...GarySP — 11:31 AM
Shadow Meter Bulb
Any 6.3 volt pilot light will work. I would use the brightest one I could find in my workroom. Be sure the dial is clean...RodB — 10:45 AM
HiFi (Chifi) tube amp build - but my own design.
Tim, nice write up and thanks for sharing !! Sincerely Richardradiorich — 02:47 AM
HiFi (Chifi) tube amp build - but my own design.
Well, this was a real "Hum-Dinger" :lol: ! This will be kinda long, but hopefully it will help others having t...TV MAN — 01:55 AM
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM

[-]
Who's Online
There are currently 7820 online users. [Complete List]
» 1 Member(s) | 7819 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Home Radios