1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Troubleshooting a 48-200
Radioroslyn
Phorum Expert
*****
Posts: 7,286
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
#4

01-26-2013, 09:03 AM
Well the simplest way to figure it out is that one of the wires from the loop goes to it.( the trimmer) Tune dial to a station near 1400kc and then adj trimmer for max volume. Should peak near middle of the range of the screw. Not all the away in (if so then take a turn off of the loop) or all the way out (Add a turn to the loop) till your in the middle. Perfect!!
GL
Terry
ps r u in PA??
Find
« Next Oldest | Next Newest »


Messages In This Thread
Troubleshooting a 48-200 - by winkydink - 01-24-2013, 11:35 PM
RE: Troubleshooting a 48-200 - by 7estatdef - 01-25-2013, 04:49 PM
RE: Troubleshooting a 48-200 - by winkydink - 01-26-2013, 08:40 AM
RE: Troubleshooting a 48-200 - by 7estatdef - 01-26-2013, 09:03 AM
RE: Troubleshooting a 48-200 - by winkydink - 01-27-2013, 11:34 PM
RE: Troubleshooting a 48-200 - by codefox1 - 01-27-2013, 11:39 PM
RE: Troubleshooting a 48-200 - by winkydink - 01-31-2013, 08:10 AM
RE: Troubleshooting a 48-200 - by winkydink - 02-05-2013, 10:42 AM
RE: Troubleshooting a 48-200 - by Steve Davis - 02-05-2013, 01:38 PM
RE: Troubleshooting a 48-200 - by winkydink - 02-05-2013, 07:54 PM
RE: Troubleshooting a 48-200 - by winkydink - 02-05-2013, 10:57 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently 4947 online users. [Complete List]
» 1 Member(s) | 4946 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration