1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
RF Can Removal 42-340
Arran
Phorum Expert
*****
Posts: 4,703
Threads: 51
Joined: Sep 2008
City: Sandwick, BC, CA
#3

01-27-2013, 12:05 AM
I would unsolder the wires and remove the can from the chassis first before removing the clip. Taking it out isn't too hard but getting it back in is a different story if it's still attached to the chassis. It's sort of hard to explain how to remove it, the slit works like a key way where you have to lift it up on both sides and push it over so it will slide or fall out.
Regards
Arran
Find
« Next Oldest | Next Newest »


Messages In This Thread
RF Can Removal 42-340 - by propflux01 - 01-26-2013, 09:46 PM
RE: RF Can Removal 42-340 - by klondike98 - 01-26-2013, 11:34 PM
RE: RF Can Removal 42-340 - by Arran - 01-27-2013, 12:05 AM
RE: RF Can Removal 42-340 - by propflux01 - 01-27-2013, 02:46 AM
RE: RF Can Removal 42-340 - by klondike98 - 01-27-2013, 09:12 AM
RE: RF Can Removal 42-340 - by codefox1 - 01-27-2013, 10:13 AM
RE: RF Can Removal 42-340 - by propflux01 - 01-27-2013, 11:45 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently 4823 online users. [Complete List]
» 1 Member(s) | 4822 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration