38-116 repair help

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

38-116 repair help

Radioroslyn
Phorum Expert

Posts: 7,286
Threads: 268
Joined: Dec 2009
City: Roslyn Pa

01-27-2013, 09:28 PM

Years and years ago I serviced my 37-116 and did the same thing you did. Replaced all the caps I could get to without digging deep into the RF sub chassis. It played well for a number of years till one day it died. Everything looked good but wouldn't pass a RF signal. So after some troubleshooting it came down to a shorted cap on the screen of the osc tube. I had no local oscillator. It took a bit of doing but I was able to get it replaced. Set was back to working great again.
Terry
Still have three RF chassis I need to pull out and repair.

(This post was last modified: 01-27-2013, 09:29 PM by Radioroslyn.)

Find

« Next Oldest | Next Newest »

Messages In This Thread

38-116 repair help - by murf - 01-27-2013, 06:20 PM

RE: 38-116 repair help - by dixierat - 01-27-2013, 07:58 PM

RE: 38-116 repair help - by 7estatdef - 01-27-2013, 09:28 PM

RE: 38-116 repair help - by jerryhawthorne - 01-28-2013, 10:52 PM

RE: 38-116 repair help - by murf - 01-28-2013, 11:13 PM

RE: 38-116 repair help - by morzh - 01-28-2013, 11:22 PM

RE: 38-116 repair help - by 7estatdef - 01-28-2013, 11:29 PM

RE: 38-116 repair help - by SteveJB - 01-28-2013, 11:30 PM

RE: 38-116 repair help - by jerryhawthorne - 01-28-2013, 11:56 PM

RE: 38-116 repair help - by Phlogiston - 01-29-2013, 04:23 AM

RE: 38-116 repair help - by jerryhawthorne - 01-29-2013, 11:55 PM

RE: 38-116 repair help - by Arran - 01-30-2013, 01:57 AM

RE: 38-116 repair help - by Ron Ramirez - 01-30-2013, 09:12 AM

RE: 38-116 repair help - by Chuck Schwark - 01-30-2013, 10:25 AM

RE: 38-116 repair help - by murf - 01-30-2013, 10:59 AM

RE: 38-116 repair help - by Phlogiston - 01-30-2013, 10:20 PM

RE: 38-116 repair help - by Ron Ramirez - 01-31-2013, 06:42 AM

RE: 38-116 repair help - by jerryhawthorne - 01-31-2013, 06:37 PM

RE: 38-116 repair help - by murf - 01-31-2013, 06:56 PM

RE: 38-116 repair help - by jerryhawthorne - 01-31-2013, 07:06 PM

RE: 38-116 repair help - by murf - 01-31-2013, 08:41 PM

RE: 38-116 repair help - by Ron Ramirez - 01-31-2013, 09:30 PM

RE: 38-116 repair help - by Phlogiston - 01-31-2013, 10:48 PM

RE: 38-116 repair help - by jerryhawthorne - 02-01-2013, 12:03 AM

View a Printable Version

Users browsing this thread: 2 Guest(s)

Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

Who's Online

There are currently 5615 online users. [Complete List]
» 1 Member(s) | 5614 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me