1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Other Radios (Non-Philco)
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Mitchell 1264 Issues
rghines1
Member
***
Posts: 190
Threads: 8
Joined: Oct 2005
City: Lexington, SC
#7

01-29-2013, 07:29 PM
Good on the isolation transformer.

Quote:When you say "rear" gang, are you talking about the smaller one or the larger one of the two

Should be the larger, the smaller is for the oscillator.

Quote: (I am assuming you are referring to the tuning gang)?

Correct.

The trimmer is normally part of the tuning gang.
Find
« Next Oldest | Next Newest »


Messages In This Thread
Mitchell 1264 Issues - by propflux01 - 01-27-2013, 12:20 PM
RE: Mitchell 1264 Issues - by 7estatdef - 01-27-2013, 10:09 PM
RE: Mitchell 1264 Issues - by propflux01 - 01-27-2013, 11:24 PM
RE: Mitchell 1264 Issues - by rghines1 - 01-28-2013, 07:19 PM
RE: Mitchell 1264 Issues - by propflux01 - 01-29-2013, 11:11 AM
RE: Mitchell 1264 Issues - by 7estatdef - 01-29-2013, 06:04 PM
RE: Mitchell 1264 Issues - by rghines1 - 01-29-2013, 07:29 PM
RE: Mitchell 1264 Issues - by propflux01 - 01-29-2013, 10:55 PM
RE: Mitchell 1264 Issues - by 7estatdef - 01-30-2013, 09:24 AM
RE: Mitchell 1264 Issues - by propflux01 - 01-31-2013, 01:29 PM
RE: Mitchell 1264 Issues - by rghines1 - 01-31-2013, 08:03 PM
RE: Mitchell 1264 Issues - by propflux01 - 02-01-2013, 08:01 PM
RE: Mitchell 1264 Issues - by rghines1 - 02-02-2013, 11:28 AM
RE: Mitchell 1264 Issues - by propflux01 - 02-02-2013, 05:01 PM
RE: Mitchell 1264 Issues - by rghines1 - 02-02-2013, 08:37 PM
RE: Mitchell 1264 Issues - by propflux01 - 02-03-2013, 10:50 PM
RE: Mitchell 1264 Issues - by propflux01 - 02-04-2013, 04:49 PM
RE: Mitchell 1264 Issues - by rghines1 - 02-04-2013, 05:35 PM
RE: Mitchell 1264 Issues - by propflux01 - 02-04-2013, 06:26 PM
RE: Mitchell 1264 Issues - by rghines1 - 02-04-2013, 08:26 PM



Users browsing this thread: 3 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently 4604 online users. [Complete List]
» 1 Member(s) | 4603 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Other Radios (Non-Philco)