Troubleshooting a 48-200

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Troubleshooting a 48-200

winkydink
Member

Posts: 99
Threads: 24
Joined: Jan 2012
City: Cape May State, Province, Country: New Jersey

01-31-2013, 08:10 AM

Here is the latest update.

Upon the suggestion of Jeff from Radiotiques I also tested to see if the repaired speaker was a problem. So I desoldered connections used aligator clips and tested using the speaker on a "junk" Philco 47-204. The sound was very good. This is where I have stopped.

I still need to remove a loop and adjust the trimmer for max volume, so that the screw is in the middle of the range. I also need to see if I can easily remove the speaker from the 47-204. I also don't know if this speaker will fit in the 48-200 case.

Lots of unknows, but I am making some progress.....

Find

« Next Oldest | Next Newest »

Messages In This Thread

Troubleshooting a 48-200 - by winkydink - 01-24-2013, 11:35 PM

RE: Troubleshooting a 48-200 - by 7estatdef - 01-25-2013, 04:49 PM

RE: Troubleshooting a 48-200 - by winkydink - 01-26-2013, 08:40 AM

RE: Troubleshooting a 48-200 - by 7estatdef - 01-26-2013, 09:03 AM

RE: Troubleshooting a 48-200 - by winkydink - 01-27-2013, 11:34 PM

RE: Troubleshooting a 48-200 - by codefox1 - 01-27-2013, 11:39 PM

RE: Troubleshooting a 48-200 - by winkydink - 01-31-2013, 08:10 AM

RE: Troubleshooting a 48-200 - by winkydink - 02-05-2013, 10:42 AM

RE: Troubleshooting a 48-200 - by Steve Davis - 02-05-2013, 01:38 PM

RE: Troubleshooting a 48-200 - by winkydink - 02-05-2013, 07:54 PM

RE: Troubleshooting a 48-200 - by winkydink - 02-05-2013, 10:57 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

Who's Online

There are currently 5863 online users. [Complete List]
» 2 Member(s) | 5861 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me