Another 40-216 question

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Another 40-216 question

49Stude63
Member

Posts: 225
Threads: 14
Joined: Oct 2005
City: Grand Blanc, Michigan

09-30-2007, 11:11 AM

I was basing my comment about the shield on the models which I have mostly the magnetic tuning models and typically those used the 6A8G (shielded) and located on the sub-chassis. I think the function on the magnetic tuning models was also det/osc. And on other 37 non-magnetic tuning models 37-2670 (it is labled 6A8EG (but I think the EG was a suffix for being an export model, the 6K7 also has the EG suffix on the tube label. I wonder when Philco switched from shielding the 6A8 in the 37/38 models to not shield them universally?

Find

« Next Oldest | Next Newest »

Messages In This Thread

Another 40-216 question - by davemc - 09-30-2007, 07:29 AM

[No subject] - by 49Stude63 - 09-30-2007, 10:19 AM

[No subject] - by Ron Ramirez - 09-30-2007, 10:48 AM

[No subject] - by 49Stude63 - 09-30-2007, 11:11 AM

[No subject] - by davemc - 09-30-2007, 05:08 PM

[No subject] - by 49Stude63 - 09-30-2007, 05:25 PM

[No subject] - by davemc - 10-01-2007, 09:20 AM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Hi Cap'n Clock, Unfortunately, I do not have this radio. This is a shame because this should be a good performer. 2A...captainclock1988 — 03:43 PM
Philco 42-390, code 121 speaker
Using a 5W 1.5k ceramic resistor in place of the field coil and using a 4 ohm PM speaker, I was able to bring the radi...Stevelog — 02:57 PM

Who's Online

There are currently 3414 online users. [Complete List]
» 3 Member(s) | 3411 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me