New Member - Newbie question

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

New Member - Newbie question

Mr Grumpy
Junior Member

Posts: 45
Threads: 8
Joined: Jan 2013
City: Toronto Ontario

#19

02-02-2013, 08:12 PM

Okay next problem everyone, (newb question)

I'm going through the capacitor list and getting ready to place an order online when I came across a capacitor that I was unsure of. It's listed on the schematic as #81 dual .01-.01 mfd. Below is an image of the schematic and an image of the outline of # 81. It looks like a black plastic terminal strip and is actually visible in the image that Ron posted previously. My question is, is this thing a capacitor or are there capacitors inside of it? How do I replace these two .01mfd capacitors??

[Image: http://i835.photobucket.com/albums/zz278...09b0dd.jpg]

[Image: http://i835.photobucket.com/albums/zz278...568411.jpg]

Find

« Next Oldest | Next Newest »

Messages In This Thread

New Member - Newbie question - by Mr Grumpy - 01-21-2013, 05:45 PM

RE: New Member - Newbie question - by DeckApe - 01-21-2013, 08:06 PM

RE: New Member - Newbie question - by Mr Grumpy - 01-24-2013, 02:43 PM

RE: New Member - Newbie question - by TA Forbes - 01-24-2013, 02:57 PM

RE: New Member - Newbie question - by Mr Grumpy - 01-24-2013, 07:40 PM

RE: New Member - Newbie question - by klondike98 - 01-24-2013, 09:57 PM

RE: New Member - Newbie question - by TA Forbes - 01-25-2013, 12:26 AM

RE: New Member - Newbie question - by klondike98 - 01-25-2013, 11:15 AM

RE: New Member - Newbie question - by Mr Grumpy - 01-25-2013, 05:44 PM

RE: New Member - Newbie question - by Ron Ramirez - 01-25-2013, 07:43 PM

RE: New Member - Newbie question - by Eric T - 01-25-2013, 10:02 PM

RE: New Member - Newbie question - by codefox1 - 01-26-2013, 01:43 PM

RE: New Member - Newbie question - by Mr Grumpy - 01-26-2013, 03:16 PM

RE: New Member - Newbie question - by Mr Grumpy - 01-26-2013, 06:25 PM

RE: New Member - Newbie question - by TA Forbes - 01-26-2013, 07:09 PM

RE: New Member - Newbie question - by Eric T - 01-26-2013, 08:54 PM

RE: New Member - Newbie question - by codefox1 - 01-27-2013, 12:26 AM

RE: New Member - Newbie question - by Mr Grumpy - 01-29-2013, 02:39 PM

RE: New Member - Newbie question - by Mr Grumpy - 02-02-2013, 08:12 PM

RE: New Member - Newbie question - by kporter - 02-02-2013, 11:20 PM

RE: New Member - Newbie question - by Mr Grumpy - 02-03-2013, 11:49 PM

RE: New Member - Newbie question - by Mr Grumpy - 02-10-2013, 06:15 PM

RE: New Member - Newbie question - by klondike98 - 02-10-2013, 09:30 PM

RE: New Member - Newbie question - by Mr Grumpy - 02-10-2013, 11:24 PM

View a Printable Version

Users browsing this thread: 9 Guest(s)

Recent Posts
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM
Hickok AC51 tube tester
Cleaned ann contacts, switches and sockets, works great now.martinj — 11:32 AM

Who's Online

There are currently 6907 online users. [Complete List]
» 1 Member(s) | 6906 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me