1936? model 84 resistor

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

1936? model 84 resistor

brownie45
Member

Posts: 54
Threads: 8
Joined: Nov 2012
City: Wilton, Iowa

#32

02-04-2013, 08:01 AM

Haven't gotten to the coil yet. Still have to align the set. Am
going to get the "Ron Special" ball-point pen alignment tool
made this morning. The coil should be right on--counted turns
& made very sure to wind in the correct direction. Will see
what alignment will do for the old girl first.
Any idea other than humidity---what causes the Litz wire
to corrode on the coil windings? The set was obviously not
out in a barn--chassis is in very good shape for the age of
the unit. Thanks much for your help. Jim

Find

« Next Oldest | Next Newest »

Messages In This Thread

1936? model 84 resistor - by brownie45 - 01-22-2013, 03:48 PM

RE: 1936? model 84 resistor - by Ron Ramirez - 01-22-2013, 07:30 PM

RE: 1936? model 84 resistor - by brownie45 - 01-22-2013, 09:10 PM

RE: 1936? model 84 resistor - by 7estatdef - 01-26-2013, 09:30 AM

RE: 1936? model 84 resistor - by Ron Ramirez - 01-26-2013, 10:02 AM

RE: 1936? model 84 resistor - by Ron Ramirez - 01-26-2013, 10:03 AM

RE: 1936? model 84 resistor - by brownie45 - 01-26-2013, 02:50 PM

RE: 1936? model 84 resistor - by codefox1 - 01-26-2013, 03:18 PM

RE: 1936? model 84 resistor - by Ron Ramirez - 01-26-2013, 07:19 PM

RE: 1936? model 84 resistor - by brownie45 - 01-26-2013, 09:04 PM

RE: 1936? model 84 resistor - by Ron Ramirez - 01-26-2013, 09:10 PM

RE: 1936? model 84 resistor - by 7estatdef - 01-26-2013, 09:10 PM

RE: 1936? model 84 resistor - by Ron Ramirez - 01-26-2013, 09:12 PM

RE: 1936? model 84 resistor - by brownie45 - 01-26-2013, 10:41 PM

RE: 1936? model 84 resistor - by 7estatdef - 01-27-2013, 09:59 AM

RE: 1936? model 84 resistor - by brownie45 - 01-28-2013, 04:55 PM

RE: 1936? model 84 resistor - by 7estatdef - 01-28-2013, 11:48 PM

RE: 1936? model 84 resistor - by brownie45 - 01-29-2013, 07:38 AM

RE: 1936? model 84 resistor - by Ron Ramirez - 01-29-2013, 10:52 AM

RE: 1936? model 84 resistor - by brownie45 - 01-29-2013, 02:40 PM

RE: 1936? model 84 resistor - by klondike98 - 01-29-2013, 03:00 PM

RE: 1936? model 84 resistor - by Ron Ramirez - 01-29-2013, 03:16 PM

RE: 1936? model 84 resistor - by brownie45 - 01-29-2013, 03:26 PM

RE: 1936? model 84 resistor - by 7estatdef - 01-29-2013, 05:37 PM

RE: 1936? model 84 resistor - by brownie45 - 01-29-2013, 06:39 PM

RE: 1936? model 84 resistor - by 7estatdef - 01-29-2013, 08:48 PM

RE: 1936? model 84 resistor - by brownie45 - 02-01-2013, 03:49 PM

RE: 1936? model 84 resistor - by brownie45 - 02-01-2013, 04:37 PM

RE: 1936? model 84 resistor - by 7estatdef - 02-01-2013, 11:00 PM

RE: 1936? model 84 resistor - by brownie45 - 02-02-2013, 08:10 AM

RE: 1936? model 84 resistor - by 7estatdef - 02-03-2013, 10:07 PM

RE: 1936? model 84 resistor - by brownie45 - 02-04-2013, 08:01 AM

RE: 1936? model 84 resistor - by 7estatdef - 02-04-2013, 10:00 AM

RE: 1936? model 84 resistor - by brownie45 - 02-04-2013, 11:19 AM

View a Printable Version

Users browsing this thread: 2 Guest(s)

Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

Who's Online

There are currently 4861 online users. [Complete List]
» 1 Member(s) | 4860 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me