1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
No grid voltage in model 20
Danny
Member
***
Posts: 64
Threads: 22
Joined: Oct 2006
City: Acworth State, Province, Country: GA
#3

10-02-2007, 11:23 AM
Using a Fluke 23 DMM for most all measurements. Resistance for coil #2 24
ohms for pri and 7 ohms for sec. Measured other coils but forgot to record in
my notes...They are not open or shorted I can tell you that much anyway.
No noise on the 2nd RF at all. Here is link to picture of variable cap and you
can see the compensating condenser, one on each stage. Leakage across
variable cond ? Not sure what you mean. Thanks for your time and assistance.

http://img182.imagevenue.com/img.php?loc...2_71lo.JPG
Danny
Find
« Next Oldest | Next Newest »


Messages In This Thread
No grid voltage in model 20 - by Danny - 10-01-2007, 09:15 PM
[No subject] - by rickd - 10-02-2007, 09:43 AM
[No subject] - by Danny - 10-02-2007, 11:23 AM
[No subject] - by rickd - 10-02-2007, 11:15 PM
[No subject] - by Danny - 10-14-2007, 02:15 PM
[No subject] - by rickd - 10-17-2007, 04:53 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco Model 80 Transformer resistance
Just forget this number, it is useless anyway. Simply proceed with your project.morzh — 10:08 PM
Philco Model 80 Transformer resistance
My $0.02 is that it is a misprint. I tried to look up the value for the similar 84 and 37-84, and ther is no resistance...MrFixr55 — 09:51 PM
Philco Model 80 Transformer resistance
Thanks for the quick reply! Hmm...well that's good, so what am I seeing that's 1042 ohms on the schematic for the pow...Mike L — 08:46 PM
Philco Model 80 Transformer resistance
The DC resistance of the primary is 8 to 9 Ohm.morzh — 07:54 PM
Philco Model 80 Transformer resistance
I have a feeling the primary winding on the power transformer is bad. My resistance reading on the primary side is 9 ohm...Mike L — 07:48 PM
Rusty Tuning Condenser
I would try Naval Jelly and use a soaked pipe cleaner to get it where it needs to go.RossH — 06:56 PM
38-10T chassis Restoration begins
Hello Dconant , they sold mica to use as a insulator between transistors and their heatsinks too. Rob I will remove th...radiorich — 02:52 PM
38-10T chassis Restoration begins
Thanks for the info guys. I always wondered why the use of mica. Now I know.dconant — 01:52 PM
38-10T chassis Restoration begins
Most common plastics have a dielectric constant in the 3-4 range whereas mica is around 6. This means that even if you w...Steve D — 01:46 PM
38-10T chassis Restoration begins
It is acceptable but not desirable. Plastic is not an approved cap dielectric, and even though a reasonably thick piece...morzh — 11:52 AM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration