1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco 38-116 Question More Questions
jerryhawthorne
Phorum Expert
*****
Posts: 1,562
Threads: 56
Joined: Nov 2008
City: Sedona, AZ/Placentia/CA
#42

02-17-2013, 09:14 PM
Here a a couple of pictures of the finished chassis. Seems someone in the past had removed the tube shield bases from the two 6J5G tubes used in the mag tuner. Perhaps to install metal ones? Well pin 1 on either of them is unused and not tied to ground. Seems to work well, the mag tuning so unless someone has the base and shield, does not seem to have any problems. Any thoughts on this? My friend has found some heat shrink tubing large enough to work as a spacer/insulator so off again with that and a new dial, of which the one on it has been "cleaned" by someone using water. Dang, more taking apart on that.

[Image: http://i303.photobucket.com/albums/nn129...8-1161.jpg]

[Image: http://i303.photobucket.com/albums/nn129...8-1162.jpg]
A friend in need is a pest!  Bill Slee ca 1970.
Find
« Next Oldest | Next Newest »


Messages In This Thread
RE: Philco 38-116 Question - by jerryhawthorne - 01-26-2013, 07:17 PM
RE: Philco 38-116 Question - by Phlogiston - 01-26-2013, 08:30 PM
RE: Philco 38-116 Question - by Ron Ramirez - 01-26-2013, 09:44 PM
RE: Philco 38-116 Question - by jerryhawthorne - 01-26-2013, 10:12 PM
RE: Philco 38-116 Question - by jerryhawthorne - 01-26-2013, 10:34 PM
RE: Philco 38-116 Question - by jerryhawthorne - 01-29-2013, 12:03 AM
RE: Philco 38-116 Question - by Phlogiston - 01-29-2013, 04:16 AM
RE: Philco 38-116 Question - by jerryhawthorne - 01-29-2013, 02:16 PM
RE: Philco 38-116 Question - by jerryhawthorne - 01-31-2013, 09:16 PM
RE: Philco 38-116 Question - by Phlogiston - 01-31-2013, 11:04 PM
RE: Philco 38-116 Question - by jerryhawthorne - 02-01-2013, 12:10 AM
RE: Philco 38-116 Question - by Phlogiston - 02-01-2013, 03:34 AM
RE: Philco 38-116 Question More Questions - by jerryhawthorne - 02-17-2013, 09:14 PM



Users browsing this thread: 4 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration