Crosley 515 trouble shooting

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Crosley 515 trouble shooting

morzh
Odobenus rosmarus

Posts: 15,832
Threads: 554
Joined: Oct 2011
City: Jackson, NJ

02-18-2013, 09:06 PM

Eric

Considering tolerances this is a good agreement. Also the 21Z/Y are parallelled by tubes' screen grids so that lowers their resistances some resulting in higher voltage than calculated. Without the tubes the result, if the tolerances are good, would be closer.
So, yes what you see is OK.

Find

« Next Oldest | Next Newest »

Messages In This Thread

Crosley 515 trouble shooting - by Eric - 02-17-2013, 05:31 PM

RE: Crosley 515 trouble shooting - by morzh - 02-17-2013, 07:35 PM

RE: Crosley 515 trouble shooting - by Eric - 02-17-2013, 08:57 PM

RE: Crosley 515 trouble shooting - by morzh - 02-17-2013, 10:27 PM

RE: Crosley 515 trouble shooting - by Eric - 02-17-2013, 11:36 PM

RE: Crosley 515 trouble shooting - by morzh - 02-18-2013, 10:55 AM

RE: Crosley 515 trouble shooting - by Eric - 02-18-2013, 01:01 PM

RE: Crosley 515 trouble shooting - by morzh - 02-18-2013, 09:06 PM

RE: Crosley 515 trouble shooting - by Eric - 02-18-2013, 09:43 PM

RE: Crosley 515 trouble shooting - by morzh - 02-19-2013, 05:30 PM

RE: Crosley 515 trouble shooting - by Eric - 02-20-2013, 06:21 PM

RE: Crosley 515 trouble shooting - by morzh - 02-20-2013, 07:12 PM

RE: Crosley 515 trouble shooting - by Eric - 02-20-2013, 09:14 PM

RE: Crosley 515 trouble shooting - by morzh - 02-20-2013, 09:41 PM

RE: Crosley 515 trouble shooting - by Eric - 02-21-2013, 09:00 AM

RE: Crosley 515 trouble shooting - by Eric - 02-21-2013, 10:33 AM

RE: Crosley 515 trouble shooting - by morzh - 02-21-2013, 05:28 PM

RE: Crosley 515 trouble shooting - by Eric - 02-22-2013, 10:25 AM

RE: Crosley 515 trouble shooting - by morzh - 02-22-2013, 11:03 AM

RE: Crosley 515 trouble shooting - by Eric - 02-22-2013, 05:03 PM

RE: Crosley 515 trouble shooting - by morzh - 02-22-2013, 05:40 PM

RE: Crosley 515 trouble shooting - by Eric - 02-22-2013, 07:36 PM

RE: Crosley 515 trouble shooting - by Eric - 02-22-2013, 09:17 PM

RE: Crosley 515 trouble shooting - by morzh - 02-22-2013, 09:41 PM

RE: Crosley 515 trouble shooting - by 7estatdef - 02-23-2013, 06:48 PM

RE: Crosley 515 trouble shooting - by morzh - 02-23-2013, 07:30 PM

RE: Crosley 515 trouble shooting - by lumberman22 - 03-30-2014, 01:38 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Philco 60 Squealing
Usually a wave trap is for keeping IF signals from entering the antenna and from leaving the antenna. You feed an IF sig...RodB — 09:30 PM
Philco 60 Squealing
I just peaked it for the best signal at 600. NULL it for IF frequency, originally it would have been null for 500kh...Chas — 08:05 PM
Philco 60 Squealing
Wavetrap no longer matters.morzh — 05:19 PM
Philco 60 Squealing
Rod, I had checked out your suggestions but did not help. I did solder the ground rivets to the chassis as Chas suggeste...dconant — 04:52 PM
37-690 Bass Choke Replacement
Yeah, I know, Mouser and Digikey don't have "big iron" components. For some reason Philco was messing with the...Radiodial — 04:25 PM
37-690 Bass Choke Replacement
Yes, I just had to deal with that while repairing the 37-604 Philco. Exactly that value choke was gone. And the current ...morzh — 03:52 PM
37-690 Bass Choke Replacement
Ah, now where to find one. I've into this before on smaller sets, I now recall. Hammond makes one that is only rated...Radiodial — 03:27 PM
Philco 38-7 Speaker
Ask the admins to put them together. As for the renaming, while inside the thread, you simply press "New reply&quo...morzh — 02:23 PM
37-690 Bass Choke Replacement
This is the parts catalog. 32-7528 choke is 65H, 10mA, 2,250 Ohm inductance. Find a suitable one.morzh — 02:18 PM
37-690 Bass Choke Replacement
While troubleshooting the no bass amplification issue, I think I found the culprit. The choke #104 is reading 164K ohms....Radiodial — 01:42 PM

Who's Online

There are currently 2283 online users. [Complete List]
» 1 Member(s) | 2282 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me