Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Crosley 515 trouble shooting
#9

I was doing some searches on the Antique forum and came across some info that says the vol control should be 15k and not the 30k that is in the chassis so I will see about picking up one tommorow.

found some more info apparently Crosley also made this radio for United Motors model Delco 1105 their print shows a 4800ohm vol control. The print looks the same just layed out a little different it has the values on the schematic I will make a closer comparison tomorrow


Messages In This Thread
Crosley 515 trouble shooting - by Eric - 02-17-2013, 05:31 PM
RE: Crosley 515 trouble shooting - by morzh - 02-17-2013, 07:35 PM
RE: Crosley 515 trouble shooting - by Eric - 02-17-2013, 08:57 PM
RE: Crosley 515 trouble shooting - by morzh - 02-17-2013, 10:27 PM
RE: Crosley 515 trouble shooting - by Eric - 02-17-2013, 11:36 PM
RE: Crosley 515 trouble shooting - by morzh - 02-18-2013, 10:55 AM
RE: Crosley 515 trouble shooting - by Eric - 02-18-2013, 01:01 PM
RE: Crosley 515 trouble shooting - by morzh - 02-18-2013, 09:06 PM
RE: Crosley 515 trouble shooting - by Eric - 02-18-2013, 09:43 PM
RE: Crosley 515 trouble shooting - by morzh - 02-19-2013, 05:30 PM
RE: Crosley 515 trouble shooting - by Eric - 02-20-2013, 06:21 PM
RE: Crosley 515 trouble shooting - by morzh - 02-20-2013, 07:12 PM
RE: Crosley 515 trouble shooting - by Eric - 02-20-2013, 09:14 PM
RE: Crosley 515 trouble shooting - by morzh - 02-20-2013, 09:41 PM
RE: Crosley 515 trouble shooting - by Eric - 02-21-2013, 09:00 AM
RE: Crosley 515 trouble shooting - by Eric - 02-21-2013, 10:33 AM
RE: Crosley 515 trouble shooting - by morzh - 02-21-2013, 05:28 PM
RE: Crosley 515 trouble shooting - by Eric - 02-22-2013, 10:25 AM
RE: Crosley 515 trouble shooting - by morzh - 02-22-2013, 11:03 AM
RE: Crosley 515 trouble shooting - by Eric - 02-22-2013, 05:03 PM
RE: Crosley 515 trouble shooting - by morzh - 02-22-2013, 05:40 PM
RE: Crosley 515 trouble shooting - by Eric - 02-22-2013, 07:36 PM
RE: Crosley 515 trouble shooting - by Eric - 02-22-2013, 09:17 PM
RE: Crosley 515 trouble shooting - by morzh - 02-22-2013, 09:41 PM
RE: Crosley 515 trouble shooting - by 7estatdef - 02-23-2013, 06:48 PM
RE: Crosley 515 trouble shooting - by morzh - 02-23-2013, 07:30 PM
RE: Crosley 515 trouble shooting - by lumberman22 - 03-30-2014, 01:38 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Value of capacitor
If this helps you sort it out just remember 10,000 mmfd or pf = .01 mfd. So 5,000mmfd = .005 mfd.Radioroslyn — 04:23 PM
Value of capacitor
OP here- the parts list calls for an .005 1000 volt mica. It currently has an .005 1000 volt electrolytic that is at lea...bridkarl — 02:09 PM
Value of capacitor
Maybe it's one of those paper caps that is wrapped in a mica-lookiing case.RodB — 01:51 PM
Value of capacitor
I also was wondering what the post about using polarized caps had to do with the subject? The cap is 5nF, does not exis...morzh — 10:22 AM
Value of capacitor
The OP stated that there is an electrolytic in the circuit in place of the coupling cap and wondered what effect it has....RodB — 09:53 AM
Value of capacitor
According to AI... ...assuming the electrolytic that's in it now is polarized... What does your response have to ...DaleHCook — 08:17 AM
Philco 50-925 antenna connections
Most loop antenna setups are either one continuous loop with two connections or 2 loops with 4 connections. The latter c...RodB — 02:16 PM
Value of capacitor
Not trying to answer for the OP, just commenting on the thread. According to AI... ...assuming the electrolytic that'...HowardWoodard — 02:09 PM
Philco 50-925 antenna connections
Hello Keith! I've updated your thread with the proper model number. Take care, - GaryGarySP — 01:10 PM
Value of capacitor
Why are you having to replace it? Does it measure out of tolerance? Is it mechanically damaged?DaleHCook — 07:50 AM

[-]
Who's Online
There are currently no members online.

>