Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

My Philco 38-116
#9

Well, I took it to my buddy's place and the first bit of work has begun on the chassis and speaker. Speaker had a few patches in it and I do have a few trashed shield bases and four missing tube shields on the chassis. Seems to be people needed tubes during WWII and they had to get what they could get, usually the stupid metal tubes that Philco seemed to hate! At least that is my friend's theory. We brought it up slowly and it seems all the transformers and the speaker are good, but we are not getting B+ to the tubes on the tuner chassis. He is going to work on it more tonight and even thinks he might have the missing part for my tuner. We will have to see how it turns out. Icon_smile

No matter where you go, there you are.


Messages In This Thread
My Philco 38-116 - by Jayce - 03-11-2013, 12:31 PM
RE: My Philco 38-116 - by Jayce - 03-11-2013, 12:38 PM
RE: My Philco 38-116 - by jerryhawthorne - 03-11-2013, 01:15 PM
RE: My Philco 38-116 - by Ron Ramirez - 03-11-2013, 04:16 PM
RE: My Philco 38-116 - by Art Hoch - 03-11-2013, 05:19 PM
RE: My Philco 38-116 - by Jayce - 03-11-2013, 10:40 PM
RE: My Philco 38-116 - by Jayce - 03-12-2013, 01:11 AM
RE: My Philco 38-116 - by Gene Pederson - 03-12-2013, 05:54 PM
RE: My Philco 38-116 - by Jayce - 03-12-2013, 09:25 PM
RE: My Philco 38-116 - by jerryhawthorne - 03-12-2013, 10:08 PM
RE: My Philco 38-116 - by Jayce - 03-12-2013, 11:29 PM
RE: My Philco 38-116 - by jerryhawthorne - 03-13-2013, 12:13 AM
RE: My Philco 38-116 - by jerryhawthorne - 03-17-2013, 02:40 PM
RE: My Philco 38-116 - by Jayce - 03-17-2013, 05:07 PM
RE: My Philco 38-116 - by Arran - 03-18-2013, 08:36 PM
RE: My Philco 38-116 - by jerryhawthorne - 03-19-2013, 08:04 PM
RE: My Philco 38-116 - by Jayce - 03-19-2013, 09:18 PM



Users browsing this thread: 6 Guest(s)
[-]
Recent Posts
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM
Hickok AC51 tube tester
Cleaned ann contacts, switches and sockets, works great now.martinj — 11:32 AM
Model 28L
Hello, I'm restoring a Philco 28L and the output transformer is open. Part number of the transformer is 32-7020. Can...HORSTE — 10:32 AM

[-]
Who's Online
There are currently no members online.

>