37-93 hot resister

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

37-93 hot resister

Zapped
Junior Member

Posts: 11
Threads: 2
Joined: Aug 2009

08-20-2009, 10:53 PM

OK, I lifted the resister and it stayed cool. I took some voltage readings and here what I got.

The plates of the 5Y4G = 368 VAC
The center tap has 134 VAC on it
The filament voltage was 279 VDC

Let me clarify where I lifted the circuit, I lifted the connection at the 8 mf capacitor, 6A.

All ideas welcome.

Find

« Next Oldest | Next Newest »

Messages In This Thread

37-93 hot resister - by Zapped - 08-20-2009, 03:07 PM

Re: 37-93 hot resister - by philco phan - 08-20-2009, 03:28 PM

Re: 37-93 hot resister - by Zapped - 08-20-2009, 10:53 PM

Re: 37-93 hot resister - by philco phan - 08-21-2009, 10:38 AM

Re: 37-93 hot resister - by Terry Burns - 08-21-2009, 10:57 AM

Re: 37-93 hot resister - by Zapped - 08-21-2009, 03:36 PM

Re: 37-93 hot resister - by philco phan - 08-21-2009, 04:39 PM

Re: 37-93 hot resister - by Zapped - 08-22-2009, 12:09 AM

Re: 37-93 hot resister - by philco phan - 08-22-2009, 12:57 PM

Re: 37-93 hot resister - by Zapped - 08-22-2009, 01:51 PM

Re: 37-93 hot resister - by philco phan - 08-22-2009, 02:07 PM

Re: 37-93 hot resister - by Zapped - 08-22-2009, 02:12 PM

Re: 37-93 hot resister - by philco phan - 08-22-2009, 02:25 PM

Re: 37-93 hot resister - by philco phan - 08-22-2009, 02:34 PM

Re: 37-93 hot resister - by Zapped - 08-22-2009, 03:34 PM

Re: 37-93 hot resister - by philco phan - 08-22-2009, 04:01 PM

Re: 37-93 hot resister - by Zapped - 08-22-2009, 05:50 PM

Re: 37-93 hot resister - by philco phan - 08-22-2009, 07:08 PM

Re: 37-93 hot resister - by Zapped - 08-22-2009, 08:15 PM

Re: 37-93 hot resister - by philco phan - 08-22-2009, 08:26 PM

View a Printable Version

Users browsing this thread: 5 Guest(s)

Recent Posts
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me