Need part for radio

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Need part for radio

Texasrocker
Phorum Expert

Posts: 909
Threads: 117
Joined: Jun 2007

#18

03-18-2013, 12:29 AM

Whew!!, after reading all the preceeding posts, glad that power transformer survived!! Note to newbies! Never, ever,ever, plug these sets in and turn on the switch until the power supply caps have been replaced and check all wiring. And always check the field coil before applying power also. Only after that, you can safely apply ac with a variac and apply the ac voltage up very slowly and monitor the amperage current draw to primary of power transformer. May I nickname you "Lucky"?
ol"Tex.

Find

« Next Oldest | Next Newest »

Messages In This Thread

Need part for radio - by Davetalife - 03-11-2013, 10:49 PM

RE: Need part for radio - by jontz - 03-12-2013, 07:36 AM

RE: Need part for radio - by morzh - 03-12-2013, 01:48 PM

RE: Need part for radio - by jerryhawthorne - 03-12-2013, 06:44 PM

RE: Need part for radio - by Davetalife - 03-13-2013, 02:06 AM

RE: Need part for radio - by jerryhawthorne - 03-13-2013, 03:15 AM

RE: Need part for radio - by Davetalife - 03-14-2013, 02:03 AM

RE: Need part for radio - by jontz - 03-14-2013, 07:24 AM

RE: Need part for radio - by Davetalife - 03-14-2013, 03:28 PM

RE: Need part for radio - by DKinYORKpa - 03-14-2013, 04:00 PM

RE: Need part for radio - by klondike98 - 03-14-2013, 04:40 PM

RE: Need part for radio - by ipwizard - 03-14-2013, 06:52 PM

RE: Need part for radio - by Ron Ramirez - 03-14-2013, 07:02 PM

RE: Need part for radio - by jerryhawthorne - 03-14-2013, 08:10 PM

RE: Need part for radio - by Davetalife - 03-15-2013, 09:33 PM

RE: Need part for radio - by 7estatdef - 03-15-2013, 10:15 PM

RE: Need part for radio - by jerryhawthorne - 03-15-2013, 10:52 PM

RE: Need part for radio - by Texasrocker - 03-18-2013, 12:29 AM

RE: Need part for radio - by Davetalife - 03-19-2013, 11:19 PM

RE: Need part for radio - by Davetalife - 03-19-2013, 11:21 PM

RE: Need part for radio - by jerryhawthorne - 03-19-2013, 11:57 PM

RE: Need part for radio - by morzh - 03-20-2013, 02:41 PM

RE: Need part for radio - by jerryhawthorne - 03-20-2013, 04:48 PM

RE: Need part for radio - by Steve Davis - 03-20-2013, 05:56 PM

RE: Need part for radio - by Davetalife - 03-29-2013, 05:50 AM

View a Printable Version

Users browsing this thread: 2 Guest(s)

Recent Posts
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM
IF can wire size and Rubber mounts?
A pair of wire strippers can give you an idea of what the existing gauge of the wire leads are in the IF can, I think it...Arran — 06:07 AM
My last cabinet for this year
Hello Dan, That is really beautiful what great looking radio you have ! I have friends who live in Calgary and the wea...radiorich — 01:51 AM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me