1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
It's Alive!!!
Arran
Phorum Expert
*****
Posts: 4,703
Threads: 51
Joined: Sep 2008
City: Sandwick, BC, CA
#17

03-22-2013, 11:18 PM
Is this the original or the replacement motor? If anything a 25 cycle motor should be trying to take off down a runway on 60 cycle as AC motors are governed by line frequency, if it's too slow then the mechanical governor I see on one end may have something to do with it.
Regards
Arran
Find
« Next Oldest | Next Newest »


Messages In This Thread
It's Alive!!! - by Mr Grumpy - 02-11-2013, 04:28 PM
RE: It's Alive!!! - by klondike98 - 02-11-2013, 05:09 PM
RE: It's Alive!!! - by Mr Grumpy - 02-12-2013, 01:21 PM
RE: It's Alive!!! - by jerryhawthorne - 02-12-2013, 01:35 PM
RE: It's Alive!!! - by marv - 02-12-2013, 04:37 PM
RE: It's Alive!!! - by jerryhawthorne - 02-12-2013, 05:58 PM
RE: It's Alive!!! - by Mr Grumpy - 02-13-2013, 12:23 AM
RE: It's Alive!!! - by Eric T - 02-14-2013, 10:20 PM
RE: It's Alive!!! - by jerryhawthorne - 02-14-2013, 10:31 PM
RE: It's Alive!!! - by wa2ise - 02-14-2013, 11:50 PM
RE: It's Alive!!! - by TA Forbes - 02-15-2013, 01:24 AM
RE: It's Alive!!! - by Mr Grumpy - 02-16-2013, 09:49 PM
RE: It's Alive!!! - by Mr Grumpy - 02-27-2013, 01:09 PM
RE: It's Alive!!! - by Mr Grumpy - 03-20-2013, 09:48 PM
RE: It's Alive!!! - by 7estatdef - 03-22-2013, 09:47 PM
RE: It's Alive!!! - by Mr Grumpy - 03-22-2013, 10:58 PM
RE: It's Alive!!! - by Arran - 03-22-2013, 11:18 PM
RE: It's Alive!!! - by Mr Grumpy - 03-22-2013, 11:55 PM
RE: It's Alive!!! - by Arran - 03-23-2013, 03:18 AM
RE: It's Alive!!! - by Steve Davis - 03-23-2013, 02:27 PM
RE: It's Alive!!! - by 7estatdef - 03-23-2013, 06:19 PM
RE: It's Alive!!! - by Mr Grumpy - 03-23-2013, 10:01 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM
IF can wire size and Rubber mounts?
A pair of wire strippers can give you an idea of what the existing gauge of the wire leads are in the IF can, I think it...Arran — 06:07 AM
My last cabinet for this year
Hello Dan, That is really beautiful what great looking radio you have ! I have friends who live in Calgary and the wea...radiorich — 01:51 AM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration