1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Buzzing between stations
Radioroslyn
Phorum Expert
*****
Posts: 7,286
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
#7

04-03-2013, 04:59 PM
Well unfortunately the RF environment isn't as good (clean) as it use to be. Using a coax feed ant may tend to help. Having a good earth gnd can't hurt. And a good long high up ant is a good thing to. Noise is everywhere!!! and it,s very annoying!!
GL w/it
Terry
ps A loop ant may be a good thing as you can use it to null out the noise as much as possible.
Find
« Next Oldest | Next Newest »


Messages In This Thread
Buzzing between stations - by morzh - 04-02-2013, 09:00 PM
RE: Buzzing between stations - by BrendaAnnD - 04-02-2013, 09:24 PM
RE: Buzzing between stations - by 7estatdef - 04-03-2013, 08:16 AM
RE: Buzzing between stations - by BrendaAnnD - 04-03-2013, 09:53 AM
RE: Buzzing between stations - by morzh - 04-03-2013, 10:41 AM
RE: Buzzing between stations - by jerryhawthorne - 04-03-2013, 04:42 PM
RE: Buzzing between stations - by 7estatdef - 04-03-2013, 04:59 PM
RE: Buzzing between stations - by morzh - 04-03-2013, 11:05 PM
RE: Buzzing between stations - by Mondial - 04-04-2013, 03:48 PM
RE: Buzzing between stations - by morzh - 04-04-2013, 06:46 PM
RE: Buzzing between stations - by GarySP - 04-06-2013, 03:32 PM
RE: Buzzing between stations - by morzh - 04-06-2013, 04:30 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration