1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco 41-296 Troubles
w5ami
Junior Member
**
Posts: 31
Threads: 6
Joined: Apr 2013
City: Arkansas
#3

04-04-2013, 07:46 AM
Jerry,

Thanks for the reply. I just woke up, so hope I can make sense..

I measured 49 volts on the Osc plate and 15v on the cathode, however that was with the switch in position 1 where the schematic shows it set, not the BC band. I also measured 85v on the plate of the 1st det. (RF amp/mixer). Yes, I did have the audio on with the signal gen. @ 1000 hz. I plan to re install the gimmic today and look again. I've got some cap legs lifted for testing I need to re-solder this morning before I turn it back on. I will recheck the voltages in the BC band position and a few other things and post back here. Thanks Again!

Brian
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
Philco 41-296 Troubles - by w5ami - 04-03-2013, 05:13 PM
RE: Philco 41-296 Troubles - by jerryhawthorne - 04-03-2013, 10:03 PM
RE: Philco 41-296 Troubles - by w5ami - 04-04-2013, 07:46 AM
RE: Philco 41-296 Troubles - by 7estatdef - 04-04-2013, 02:05 PM
RE: Philco 41-296 Troubles - by w5ami - 04-05-2013, 05:15 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco model #20
Hello again fellows , well I powered up the set this evening after I had changed every cap and resistor in this set and ...onlyrick — 09:34 PM
Zenith H725
Yes - better it happened on the repair bench than returning to the owner. The other question is - do I also dissect a...EdHolland — 09:08 PM
Zenith H725
That's a bummer but get them now. Paul BPaul Philco322 — 08:27 PM
Zenith H725
I completed the insulation on the cabinet interior (Al foil and hi temp silicone rubber), and reglued the speaker gasket...EdHolland — 06:18 PM
HiFi (Chifi) tube amp build - but my own design.
Tim - Photos of 8 octal tube sockets. (Top and bottom) Send me a PM if you're interested.RodB — 04:11 PM
VTVM meter moves when my hand is next to it & not on
Haha! I hope so. It seemed rather lost and forgotten languishing in the frozen Northeast of England.EdHolland — 02:36 PM
VTVM meter moves when my hand is next to it & not on
Ed - it's in the Cayman's enjoying the good life.RodB — 02:14 PM
VTVM meter moves when my hand is next to it & not on
Static electricity - but the other chaps beat me to it again. I've seen this before with analogue meters. I've also ...EdHolland — 01:56 PM
Need to purchase some accessories for restoration of my Old Philco Radio
Hi Paulo, Welcome to the Philco Phorum. I can see why you want to find good reproduction parts. That is a bea...MrFixr55 — 11:10 PM
HiFi (Chifi) tube amp build - but my own design.
Tim, I have some bakelite sockets in my work shop that I can dig up. I believe quite a few are NOS. I will take photo...RodB — 10:03 PM

[-]
Who's Online
There are currently 1338 online users. [Complete List]
» 3 Member(s) | 1335 Guest(s)
AvatarAvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration