1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Other Radios (Non-Philco)
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Stromberg Carlson 180L
Paul Philco322
Super Moderator
******
Posts: 4,381
Threads: 412
Joined: Jun 2011
City: Boston State, Province, Country: Massachusetts
#9

05-10-2013, 08:54 PM
That dial is a beaut. Stromberg Carlson was out of Rochester NY. Made Telephone equipment and did a lot of that for the Government. Their build quality is very good. I have a couple of consoles, I have a little 6 tube job from the 40's they made, it weighs 3x most sets it size and is a great little performer.

I would take it, where did you put these monsters?

Paul
Tubetalk1
Website Find
« Next Oldest | Next Newest »


Messages In This Thread
Stromberg Carlson 180L - by TA Forbes - 05-04-2013, 02:55 PM
RE: Stromberg Carlson 180L - by Arran - 05-04-2013, 09:18 PM
RE: Stromberg Carlson 180L - by TA Forbes - 05-04-2013, 10:22 PM
RE: Stromberg Carlson 180L - by Jayce - 05-04-2013, 11:57 PM
RE: Stromberg Carlson 180L - by Phlogiston - 05-05-2013, 03:26 AM
RE: Stromberg Carlson 180L - by TA Forbes - 05-05-2013, 11:36 AM
RE: Stromberg Carlson 180L - by moneyrad - 05-05-2013, 11:13 PM
RE: Stromberg Carlson 180L - by TA Forbes - 05-06-2013, 04:13 PM
RE: Stromberg Carlson 180L - by Paul Philco322 - 05-10-2013, 08:54 PM
RE: Stromberg Carlson 180L - by M Desht - 05-30-2013, 06:12 PM
RE: Stromberg Carlson 180L - by rocketeer - 06-05-2013, 02:43 PM
RE: Stromberg Carlson 180L - by morzh - 06-05-2013, 05:23 PM
RE: Stromberg Carlson 180L - by TA Forbes - 06-05-2013, 11:35 PM
RE: Stromberg Carlson 180L - by morzh - 06-05-2013, 11:53 PM
RE: Stromberg Carlson 180L - by TA Forbes - 06-06-2013, 11:33 AM



Users browsing this thread: 3 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently 5812 online users. [Complete List]
» 2 Member(s) | 5810 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Other Radios (Non-Philco)