5Y3 question

Thread Rating:

5Y3 question

BrendaAnnD
Phorum Expert

Posts: 1,108
Threads: 89
Joined: Jun 2011
City: Tacoma State, Province, Country: Washington

#14

05-17-2013, 02:25 AM

I don't count any tube as "HOT" if I can pull it by holding onto its base immediately after turning the device off. Icon_smile

Find

« Next Oldest | Next Newest »

Messages In This Thread

5Y3 question - by shaler78 - 05-07-2013, 10:35 PM

RE: 5Y3 question - by BrendaAnnD - 05-07-2013, 10:52 PM

RE: 5Y3 question - by morzh - 05-07-2013, 10:52 PM

RE: 5Y3 question - by Mondial - 05-07-2013, 10:57 PM

RE: 5Y3 question - by shaler78 - 05-07-2013, 11:33 PM

RE: 5Y3 question - by gary rabbitt - 05-14-2013, 08:30 PM

RE: 5Y3 question - by codefox1 - 05-16-2013, 01:31 PM

RE: 5Y3 question - by morzh - 05-16-2013, 02:09 PM

RE: 5Y3 question - by shaler78 - 05-16-2013, 07:40 PM

RE: 5Y3 question - by gary rabbitt - 05-17-2013, 12:00 AM

RE: 5Y3 question - by shaler78 - 05-17-2013, 12:14 AM

RE: 5Y3 question - by BrendaAnnD - 05-17-2013, 12:29 AM

RE: 5Y3 question - by Arran - 05-17-2013, 01:11 AM

RE: 5Y3 question - by BrendaAnnD - 05-17-2013, 02:25 AM

RE: 5Y3 question - by Marsupial - 05-17-2013, 10:13 AM

RE: 5Y3 question - by codefox1 - 05-17-2013, 01:15 PM

Users browsing this thread: 3 Guest(s)

Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

Who's Online

There are currently 4723 online users. [Complete List]
» 1 Member(s) | 4722 Guest(s)