Can't leave well enough alone-48-482

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Can't leave well enough alone-48-482

Eric Adams
Phorum Expert

Posts: 825
Threads: 113
Joined: Aug 2012
City: The Villages State, Province, Country: Florida

#17

05-17-2013, 08:42 PM

Thanks Morzh, I get no signal at all unless I touch it with the metal screwdriver. This is the only can I touched. The reason I dug into it was because the trimmer stopped responding and then quit. I'll check those things and get back to you.

Eric
The Villages, FL
Member: Philco Phorum, ARF, ARCI & Radiomuseum.org

Website Find

« Next Oldest | Next Newest »

Messages In This Thread

Can't leave well enough alone-48-482 - by Eric Adams - 05-16-2013, 04:03 PM

RE: Can't leave well enough alone-48-482 - by mgutierres - 05-16-2013, 04:43 PM

RE: Can't leave well enough alone-48-482 - by mgutierres - 05-16-2013, 04:47 PM

RE: Can't leave well enough alone-48-482 - by Eric Adams - 05-16-2013, 06:45 PM

RE: Can't leave well enough alone-48-482 - by mgutierres - 05-16-2013, 08:29 PM

RE: Can't leave well enough alone-48-482 - by morzh - 05-16-2013, 08:52 PM

RE: Can't leave well enough alone-48-482 - by mgutierres - 05-16-2013, 09:12 PM

RE: Can't leave well enough alone-48-482 - by mgutierres - 05-16-2013, 09:13 PM

RE: Can't leave well enough alone-48-482 - by Eric Adams - 05-17-2013, 10:00 AM

RE: Can't leave well enough alone-48-482 - by morzh - 05-17-2013, 11:42 AM

RE: Can't leave well enough alone-48-482 - by codefox1 - 05-17-2013, 01:08 PM

RE: Can't leave well enough alone-48-482 - by Eric Adams - 05-17-2013, 01:13 PM

RE: Can't leave well enough alone-48-482 - by morzh - 05-17-2013, 02:12 PM

RE: Can't leave well enough alone-48-482 - by Eric Adams - 05-17-2013, 02:44 PM

RE: Can't leave well enough alone-48-482 - by Mondial - 05-17-2013, 03:02 PM

RE: Can't leave well enough alone-48-482 - by morzh - 05-17-2013, 04:35 PM

RE: Can't leave well enough alone-48-482 - by Eric Adams - 05-17-2013, 08:42 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
trying to identify this wire type
Thanks to all for the feedback. As Arran said, it is probably an older replacement and yes it has a grid cap so I will ...georgetownjohn — 09:32 PM
trying to identify this wire type
It's possible that the red wire, actually a grid cap lead, is a very old replacement, I can't remember seeing a pre 1939...Arran — 09:18 PM
Gilfillan Brothers Car Radio?
Hi everyone, Special thanks to Joe Rossi for tracking down this obscure radio and thanks to others who took up the hun...Antipodal — 08:15 PM
trying to identify this wire type
Here's one source for your wire of many. Take care and BE HEALTHY! Gary P.S. Can't get the right color you need? I ...GarySP — 06:40 PM
trying to identify this wire type
...and modern wire of the appropriate gauges and insulation V-rating (300V minimum, usually shown right on the wire) is ...morzh — 05:47 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
I have a question about this radio, is there anyone that has access to this radio that has an intact unmolested speaker ...captainclock1988 — 04:28 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Well what makes me confuse all of those companies is that all three of those companies (Setchell-Carlson, Stromberg-Carl...captainclock1988 — 04:21 PM
trying to identify this wire type
The red wire is rubber covered wire. The others are cotton braid over rubber often in colors or a tracer, also strand...Chas — 02:43 PM
trying to identify this wire type
Greetings Phorum members, Hope you can help me identify this type of wire in the photo I have attached. I am not sure ...georgetownjohn — 01:53 PM
Philco 60 Squealing
All correct shields must be in place, all tubes correct no subs of any kind. Check any soldered, riveted ground conne...Chas — 01:24 PM

Who's Online

There are currently 5144 online users. [Complete List]
» 1 Member(s) | 5143 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me