Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Zenith...over rated or not!
#24

Since you brought it up, the 12S568/69 and 12S595 are very good sounding sets. They often fall under the "ignored" Z's.

However, they also fall under the "padding the tube count" type of Z's that I mentioned previously. Two 6X5s, two 6J5s serving as oscillator and 2d detector, and three 6J5s driving/inverting the PP6V6s. Also, there is only ONE I.F. amp.

In my opinion this design sacrifices ability to pull in distant stations, which is something I would think the buyer of an expensive high-tube count set would want.


Messages In This Thread
Zenith...over rated or not! - by 462ron - 05-18-2013, 08:59 PM
RE: Zenith...over rated or not! - by Ron Ramirez - 05-18-2013, 09:10 PM
RE: Zenith...over rated or not! - by 462ron - 05-18-2013, 09:32 PM
RE: Zenith...over rated or not! - by Ron Ramirez - 05-18-2013, 09:49 PM
RE: Zenith...over rated or not! - by w4rtc - 05-18-2013, 09:55 PM
RE: Zenith...over rated or not! - by Arran - 05-18-2013, 09:57 PM
RE: Zenith...over rated or not! - by BrendaAnnD - 05-19-2013, 01:00 AM
RE: Zenith...over rated or not! - by Ron Ramirez - 05-19-2013, 07:45 AM
RE: Zenith...over rated or not! - by w4rtc - 05-19-2013, 03:08 PM
RE: Zenith...over rated or not! - by GarySP - 05-19-2013, 03:22 PM
RE: Zenith...over rated or not! - by Ron Ramirez - 05-19-2013, 03:28 PM
RE: Zenith...over rated or not! - by TA Forbes - 05-19-2013, 03:32 PM
RE: Zenith...over rated or not! - by morzh - 05-19-2013, 03:41 PM
RE: Zenith...over rated or not! - by codefox1 - 05-19-2013, 04:03 PM
RE: Zenith...over rated or not! - by Eliot Ness - 05-19-2013, 09:09 PM
RE: Zenith...over rated or not! - by Arran - 05-19-2013, 10:51 PM
RE: Zenith...over rated or not! - by BrendaAnnD - 05-20-2013, 12:48 AM
RE: Zenith...over rated or not! - by morzh - 05-20-2013, 08:31 AM
RE: Zenith...over rated or not! - by Jayce - 05-20-2013, 02:49 PM
RE: Zenith...over rated or not! - by TA Forbes - 05-20-2013, 07:23 PM
RE: Zenith...over rated or not! - by Arran - 05-21-2013, 09:51 PM
RE: Zenith...over rated or not! - by Ron Ramirez - 05-22-2013, 06:36 AM
RE: Zenith...over rated or not! - by murf - 05-24-2013, 11:06 AM
RE: Zenith...over rated or not! - by GarySP - 05-25-2013, 08:13 PM
RE: Zenith...over rated or not! - by murf - 05-25-2013, 08:56 PM
RE: Zenith...over rated or not! - by jcr1972 - 06-01-2013, 02:55 AM
RE: Zenith...over rated or not! - by TA Forbes - 06-01-2013, 10:01 PM
RE: Zenith...over rated or not! - by Ron Ramirez - 06-01-2013, 10:15 PM
RE: Zenith...over rated or not! - by w4rtc - 06-01-2013, 10:56 PM
RE: Zenith...over rated or not! - by Eliot Ness - 06-02-2013, 12:36 PM
RE: Zenith...over rated or not! - by Art Hoch - 06-03-2013, 10:15 PM
RE: Zenith...over rated or not! - by rocketeer - 06-04-2013, 10:13 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Cannot Adjust an IF Transformer’s cores
Outstanding work indeed. I wish I could come up with solutions like this.slford310 — 11:16 PM
Cannot Adjust an IF Transformer’s cores
The abilities of our 'Phorum Pholks" never ceases to amaze me! Fantastic fabrication, Joseph! I'm waiting now for...GarySP — 08:27 PM
PT-6 antenna connections
Thanks. I never realized that was a notch noted in the schematic as described. I’ll recheck my wiring.bridkarl — 08:13 PM
Cannot Adjust an IF Transformer’s cores
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM

[-]
Who's Online
There are currently no members online.

>