1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Home Radios
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
37-610
Arran
Phorum Expert
*****
Posts: 4,639
Threads: 51
Joined: Sep 2008
City: Sandwick, BC, CA
#21

05-24-2013, 06:56 PM
No I wasn't bashing the 37-610 in and of itself, I just wouldn't think of paying $200 for one just because the faux grain is in nice shape. Because these sets were a near entry level model there were a lot of them produced. While the faux grain is bad on a lot of them it's not like it's anywhere near impossible to find one where the grain, if not pristine, is at least restorable like the front panel on Bob's 38-62.
Regards
Arran
Find
« Next Oldest | Next Newest »


Messages In This Thread
37-610 - by Eric Adams - 04-23-2013, 06:30 PM
RE: 37-610 - by Ron Ramirez - 04-23-2013, 06:48 PM
RE: 37-610 - by GarySP - 04-23-2013, 06:53 PM
RE: 37-610 - by Eric Adams - 04-23-2013, 07:29 PM
RE: 37-610 - by GarySP - 04-23-2013, 09:05 PM
RE: 37-610 - by Eric Adams - 04-23-2013, 09:53 PM
RE: 37-610 - by GarySP - 04-24-2013, 09:17 AM
RE: 37-610 - by 7estatdef - 04-24-2013, 06:52 PM
RE: 37-610 - by Eric Adams - 04-28-2013, 07:34 PM
RE: 37-610 - by 7estatdef - 04-29-2013, 06:37 PM
RE: 37-610 - by TA Forbes - 05-01-2013, 08:57 PM
RE: 37-610 - by Arran - 05-01-2013, 09:00 PM
RE: 37-610 - by Eric Adams - 05-01-2013, 09:27 PM
RE: 37-610 - by Ron Ramirez - 05-02-2013, 07:35 AM
RE: 37-610 - by Arran - 05-02-2013, 04:29 PM
RE: 37-610 - by GarySP - 05-02-2013, 07:49 PM
RE: 37-610 - by Paul Philco322 - 05-03-2013, 09:58 AM
RE: 37-610 - by PhilcoJohn - 05-22-2013, 08:06 AM
RE: 37-610 - by TA Forbes - 05-22-2013, 08:24 AM
RE: 37-610 - by PhilcoJohn - 05-24-2013, 06:39 PM
RE: 37-610 - by Arran - 05-24-2013, 06:56 PM
RE: 37-610 - by TA Forbes - 05-25-2013, 12:48 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Cannot Adjust an IF Transformer’s cores
Outstanding work indeed. I wish I could come up with solutions like this.slford310 — 11:16 PM
Cannot Adjust an IF Transformer’s cores
The abilities of our 'Phorum Pholks" never ceases to amaze me! Fantastic fabrication, Joseph! I'm waiting now for...GarySP — 08:27 PM
PT-6 antenna connections
Thanks. I never realized that was a notch noted in the schematic as described. I’ll recheck my wiring.bridkarl — 08:13 PM
Cannot Adjust an IF Transformer’s cores
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Home Radios