1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco Mod. 144 help needed
KCMike
Phorum Expert
*****
Posts: 1,475
Threads: 69
Joined: Nov 2012
City: Kansas city, MO.
#9

05-31-2013, 08:18 PM
Its a fluke mod. 73III multi range tester. I did these test as per philco voltage chart with settings as described in the chart. I got all the info and and enlarged schematic from Chuck Schwark. I will get the rest of your questions answered as soon as I can. I have a # 67 on parts list that was a 8-8-10 cap. It had been bypassed sometime in the past so I took out the caps that they used to bypass #67 and used 10uF elect. caps 450v in there place. My parts list shows #50BC(263ohms-21ohms wire wound). I will recheck it and post result
(This post was last modified: 05-31-2013, 08:47 PM by KCMike.)
Find
« Next Oldest | Next Newest »


Messages In This Thread
Philco Mod. 144 help needed - by KCMike - 05-31-2013, 12:21 PM
RE: Philco Mod. 144 help needed - by morzh - 05-31-2013, 12:28 PM
RE: Philco Mod. 144 help needed - by KCMike - 05-31-2013, 01:06 PM
RE: Philco Mod. 144 help needed - by morzh - 05-31-2013, 01:41 PM
RE: Philco Mod. 144 help needed - by KCMike - 05-31-2013, 01:53 PM
RE: Philco Mod. 144 help needed - by morzh - 05-31-2013, 01:57 PM
RE: Philco Mod. 144 help needed - by KCMike - 05-31-2013, 06:40 PM
RE: Philco Mod. 144 help needed - by morzh - 05-31-2013, 08:01 PM
RE: Philco Mod. 144 help needed - by KCMike - 05-31-2013, 08:18 PM
RE: Philco Mod. 144 help needed - by morzh - 05-31-2013, 08:52 PM
RE: Philco Mod. 144 help needed - by KCMike - 05-31-2013, 09:17 PM
RE: Philco Mod. 144 help needed - by KCMike - 06-04-2013, 02:27 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently 5996 online users. [Complete List]
» 2 Member(s) | 5994 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration