1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco Mod. 144 help needed
morzh
Odobenus rosmarus
******
Posts: 16,481
Threads: 573
Joined: Oct 2011
City: Jackson State, Province, Country: NJ
#10

05-31-2013, 08:52 PM
I think #67 to resistor #54 is probably OK as otherwise there'd be no voltage on 75's plate. Still check it.
10uF is OK i/o 8uF.

FLuke will measure higher value as that in the sch as it is very high impedance and does not load the voltages unlike the old 10kOhm/V meters.
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
Philco Mod. 144 help needed - by KCMike - 05-31-2013, 12:21 PM
RE: Philco Mod. 144 help needed - by morzh - 05-31-2013, 12:28 PM
RE: Philco Mod. 144 help needed - by KCMike - 05-31-2013, 01:06 PM
RE: Philco Mod. 144 help needed - by morzh - 05-31-2013, 01:41 PM
RE: Philco Mod. 144 help needed - by KCMike - 05-31-2013, 01:53 PM
RE: Philco Mod. 144 help needed - by morzh - 05-31-2013, 01:57 PM
RE: Philco Mod. 144 help needed - by KCMike - 05-31-2013, 06:40 PM
RE: Philco Mod. 144 help needed - by morzh - 05-31-2013, 08:01 PM
RE: Philco Mod. 144 help needed - by KCMike - 05-31-2013, 08:18 PM
RE: Philco Mod. 144 help needed - by morzh - 05-31-2013, 08:52 PM
RE: Philco Mod. 144 help needed - by KCMike - 05-31-2013, 09:17 PM
RE: Philco Mod. 144 help needed - by KCMike - 06-04-2013, 02:27 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Refinishing Ideas
Hi Poulsbobl, I think that you could get away with it.  In the Philco Library, there is a parts listand specs for sp...MrFixr55 — 11:54 PM
Philco 46-480 Electronic Restoration
The sleeving for the transformer arrived early, so I went ahead and finished reassembling. The chassis looks far better ...jrblasde — 10:15 PM
Philco 610B oscillator wiring
I don't know what you are referring to when you say "tube cathode ground". Ground is a connection to the chass...RodB — 05:56 PM
Zenith H725
Good points, Arran. I haven't encountered this problem with any other radio (all earlier vintages), so am learning here....EdHolland — 05:32 PM
Zenith H725
Ed; One thing that I will say about these is that Brand Z was considerate enough to make these mica caps easily acces...Arran — 02:34 PM
Philco 610B oscillator wiring
Do you know what run # your chassis is? It took me a while to find what you were basing updates/modification on as I did...Radioroslyn — 07:34 AM
Need to purchase some accessories for restoration of my Old Philco Radio
COLLEAGUES, Thank you all for such good and important suggestions as how to find good replacement parts. I will go fo...palonso — 07:05 AM
Zenith H725
Here's what the inside of AM IFT2 looked like, and the other pic shows the discs I made to take place of the mica and ke...EdHolland — 07:40 PM
Zenith H725
IF2 will need replacement caps. The arcing was severe enough that the mica is pitted and holed where the HT flashed over...EdHolland — 04:04 PM
My Philco 37-116 Restore
Measuring from center tap like the tube voltages show. Cap 127 is isolated from ground. Cap 127 shown in upper left of p...dconant — 08:05 AM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration