1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco Mod. 144 help needed
KCMike
Phorum Expert
*****
Posts: 1,475
Threads: 69
Joined: Nov 2012
City: Kansas city, MO.
#11

05-31-2013, 09:17 PM
I just checked #50 bc wire wound It reads 20.9ohms and 286 ohms, not 263 as it should be. Is 286 too high? That looks like it might be hard to find a replacement for. Sorry morzh had to edit this. The speaker is the correct 660 ohm field coil 10.5 inch dia. It is an H-29 where as the original was H-16. I conversed with Ron Ramirez a while back and he said as long as it has the 660 field coil it will work but finding correct output tranny could be challenge. Thats why I bought the universal otse with the 7000ohm option for the plate load of the 42 tube.
(This post was last modified: 05-31-2013, 09:35 PM by KCMike.)
Find
« Next Oldest | Next Newest »


Messages In This Thread
Philco Mod. 144 help needed - by KCMike - 05-31-2013, 12:21 PM
RE: Philco Mod. 144 help needed - by morzh - 05-31-2013, 12:28 PM
RE: Philco Mod. 144 help needed - by KCMike - 05-31-2013, 01:06 PM
RE: Philco Mod. 144 help needed - by morzh - 05-31-2013, 01:41 PM
RE: Philco Mod. 144 help needed - by KCMike - 05-31-2013, 01:53 PM
RE: Philco Mod. 144 help needed - by morzh - 05-31-2013, 01:57 PM
RE: Philco Mod. 144 help needed - by KCMike - 05-31-2013, 06:40 PM
RE: Philco Mod. 144 help needed - by morzh - 05-31-2013, 08:01 PM
RE: Philco Mod. 144 help needed - by KCMike - 05-31-2013, 08:18 PM
RE: Philco Mod. 144 help needed - by morzh - 05-31-2013, 08:52 PM
RE: Philco Mod. 144 help needed - by KCMike - 05-31-2013, 09:17 PM
RE: Philco Mod. 144 help needed - by KCMike - 06-04-2013, 02:27 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently 5560 online users. [Complete List]
» 1 Member(s) | 5559 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration