Veneer repair and finish advice for Philco 14MX

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12, 2025) x

Thread Closed

Linear Mode

Veneer repair and finish advice for Philco 14MX

Arran
Phorum Expert

Posts: 5,650
Threads: 56
Joined: Sep 2008
City: Sandwick, BC, CA

06-01-2013, 08:35 PM

A bow to them? You mean that they are warped from top to bottom and not back to front? Sometimes you can fix that by moistening the concave side and then clamping it with a jig to hold it straight, but the sides in this set are likely laminated so I'm not sure if it would work. If the warp is from top to bottom I think it's likely that the braces on the inside at the back are also bowed so that probably has not helped matters.
Regards
Arran

Find

« Next Oldest | Next Newest »

Thread Closed

Messages In This Thread

Veneer repair and finish advice for Philco 14MX - by Groundhog74 - 05-31-2013, 06:50 AM

RE: Veneer repair and finish advice for Philco 14MX - by Art Hoch - 05-31-2013, 08:45 AM

RE: Veneer repair and finish advice for Philco 14MX - by Bob Andersen - 05-31-2013, 04:16 PM

RE: Veneer repair and finish advice for Philco 14MX - by 7estatdef - 05-31-2013, 05:54 PM

RE: Veneer repair and finish advice for Philco 14MX - by Arran - 05-31-2013, 09:26 PM

RE: Veneer repair and finish advice for Philco 14MX - by Arran - 05-31-2013, 09:45 PM

RE: Veneer repair and finish advice for Philco 14MX - by Groundhog74 - 06-01-2013, 06:36 PM

RE: Veneer repair and finish advice for Philco 14MX - by Arran - 06-01-2013, 08:35 PM

RE: Veneer repair and finish advice for Philco 14MX - by Groundhog74 - 06-02-2013, 09:39 AM

RE: Veneer repair and finish advice for Philco 14MX - by Art Hoch - 06-02-2013, 02:30 PM

RE: Veneer repair and finish advice for Philco 14MX - by Arran - 06-04-2013, 01:39 AM

RE: Veneer repair and finish advice for Philco 14MX - by Groundhog74 - 06-04-2013, 07:40 AM

RE: Veneer repair and finish advice for Philco 14MX - by Arran - 06-04-2013, 10:06 PM

RE: Veneer repair and finish advice for Philco 14MX - by Groundhog74 - 06-05-2013, 07:45 AM

RE: Veneer repair and finish advice for Philco 14MX - by Arran - 06-10-2013, 01:54 AM

RE: Veneer repair and finish advice for Philco 14MX - by Groundhog74 - 06-10-2013, 10:49 AM

RE: Veneer repair and finish advice for Philco 14MX - by Ron Ramirez - 06-10-2013, 11:02 AM

RE: Veneer repair and finish advice for Philco 14MX - by Groundhog74 - 06-10-2013, 03:22 PM

RE: Veneer repair and finish advice for Philco 14MX - by Groundhog74 - 06-10-2013, 06:35 PM

RE: Veneer repair and finish advice for Philco 14MX - by Groundhog74 - 06-10-2013, 06:40 PM

RE: Veneer repair and finish advice for Philco 14MX - by Arran - 06-10-2013, 07:44 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
54C Complete Teardown/Rebuild
Hello Roy, here is this one sincerely Richardradiorich — 12:45 AM
54C Complete Teardown/Rebuild
Richard, Had grabbed it already but thank you just the same. I find myself wanting to find some way to block out the...glyphmon — 12:03 AM
54C Complete Teardown/Rebuild
Hello roy, here is a link to the schematic . Sincerely Richardradiorich — 11:54 PM
54C Complete Teardown/Rebuild
Richard, The Silvertone 2014 also is a transformerless set, so I am incorporating a 1:1 600 ohm audio isolation transfo...glyphmon — 11:37 PM
Preliminary work on wife's Silvertone 2014
Did an alignment today which was interesting. IF alignment went great, almost all was already spot-on. Adjusting on th...glyphmon — 11:35 PM
54C Complete Teardown/Rebuild
The main problem with adding a Bluetooth input is that this set lacks a traditional power transformer to isolate it from...radiorich — 11:19 PM
54C Cabinet Refinish
I started stripping this cabinet before it got super chilly out because I knew I wasn't going to be able to work on ...glyphmon — 11:18 PM
54C Complete Teardown/Rebuild
While I'm waiting to wrap up the final steps on my wife's Silvertone 2014, I started disassembly on the next project. O...glyphmon — 11:07 PM
Preliminary work on wife's Silvertone 2014
Hello roy, that great news glad it worked out for you !! Sincerely Richardradiorich — 10:50 PM
Preliminary work on wife's Silvertone 2014
Safety caps arrived today. Soldered one in and had a successful first power-up. No magic smoke escaped and it tunes in...glyphmon — 09:53 PM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me