Philco Model 20

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Philco Model 20

GarySP
Super Moderator

Posts: 1,978
Threads: 148
Joined: Jan 2013
City: Westland, MI

#36

06-05-2013, 12:34 PM

The can points are numbered 1 through 6. Point 5 is not used in the can, but as a tie point under the chassis. Caps are installed as follows...
1.5 - between points 1 and 3
1.0 - between points 1 and 2
1.0 - between points 1 and 4
.13 - between points 2 and 6 ( I used a .15 cap here)
I used non-polarized mylar 630 volt caps for all in the can. Hope this helps> Take care. Gary

"Don't pity the dead, pity the living, above all, those living without love."
Professor Albus Dumbledore
Gary - Westland Michigan

Find

« Next Oldest | Next Newest »

Messages In This Thread

Philco Model 20 - by pete7189 - 05-16-2013, 12:34 AM

RE: Philco Model 20 - by codefox1 - 05-16-2013, 01:13 PM

RE: Philco Model 20 - by GarySP - 05-16-2013, 06:39 PM

RE: Philco Model 20 - by Arran - 05-16-2013, 07:26 PM

RE: Philco Model 20 - by GarySP - 05-16-2013, 09:58 PM

RE: Philco Model 20 - by gary rabbitt - 05-16-2013, 11:34 PM

RE: Philco Model 20 - by Arran - 05-17-2013, 03:03 AM

RE: Philco Model 20 - by pete7189 - 05-17-2013, 07:20 AM

RE: Philco Model 20 - by Mondial - 05-17-2013, 02:15 PM

RE: Philco Model 20 - by pete7189 - 05-19-2013, 11:55 PM

RE: Philco Model 20 - by Arran - 05-20-2013, 01:00 AM

RE: Philco Model 20 - by pete7189 - 05-20-2013, 03:07 AM

RE: Philco Model 20 - by GarySP - 05-20-2013, 11:03 AM

RE: Philco Model 20 - by pete7189 - 05-24-2013, 02:57 AM

RE: Philco Model 20 - by 7estatdef - 05-26-2013, 08:05 AM

RE: Philco Model 20 - by Phlogiston - 05-26-2013, 09:48 AM

RE: Philco Model 20 - by pete7189 - 05-26-2013, 06:52 PM

RE: Philco Model 20 - by Phlogiston - 05-26-2013, 07:40 PM

RE: Philco Model 20 - by morzh - 05-26-2013, 08:05 PM

RE: Philco Model 20 - by pete7189 - 05-27-2013, 01:11 AM

RE: Philco Model 20 - by Phlogiston - 05-27-2013, 09:34 AM

RE: Philco Model 20 - by morzh - 05-27-2013, 11:24 AM

RE: Philco Model 20 - by GarySP - 05-27-2013, 07:24 PM

RE: Philco Model 20 - by morzh - 05-27-2013, 08:01 PM

RE: Philco Model 20 - by pete7189 - 05-28-2013, 06:27 AM

RE: Philco Model 20 - by 7estatdef - 05-28-2013, 07:25 AM

RE: Philco Model 20 - by klondike98 - 05-28-2013, 09:30 AM

RE: Philco Model 20 - by morzh - 05-28-2013, 11:08 AM

RE: Philco Model 20 - by klondike98 - 05-28-2013, 02:09 PM

RE: Philco Model 20 - by pete7189 - 06-01-2013, 02:06 AM

RE: Philco Model 20 - by morzh - 06-01-2013, 11:35 AM

RE: Philco Model 20 - by GarySP - 06-02-2013, 04:22 PM

RE: Philco Model 20 - by pete7189 - 06-04-2013, 10:43 PM

RE: Philco Model 20 - by morzh - 06-04-2013, 10:46 PM

RE: Philco Model 20 - by pete7189 - 06-05-2013, 12:08 AM

RE: Philco Model 20 - by GarySP - 06-05-2013, 12:34 PM

RE: Philco Model 20 - by pete7189 - 06-06-2013, 04:25 AM

RE: Philco Model 20 - by GarySP - 06-06-2013, 12:24 PM

RE: Philco Model 20 - by pete7189 - 06-26-2013, 10:53 PM

RE: Philco Model 20 - by morzh - 06-26-2013, 11:11 PM

RE: Philco Model 20 - by pete7189 - 06-26-2013, 11:18 PM

RE: Philco Model 20 - by morzh - 06-27-2013, 01:36 PM

RE: Philco Model 20 - by pete7591 - 09-12-2014, 02:07 AM

RE: Philco Model 20 - by morzh - 09-12-2014, 10:15 AM

RE: Philco Model 20 - by radiohenry - 09-12-2014, 03:53 PM

View a Printable Version

Users browsing this thread: 2 Guest(s)

Recent Posts
New Philco Repair Bench
I am sure this is the archive, and not the Chuck's site.morzh — 09:50 PM
Made mistake & did not label connection
It's not like we are good friends with that wire and can tell it from other ptetty identical looking wires. Why'n't you...morzh — 09:49 PM
Made mistake & did not label connection
I'm not sure why that wire wasn't covered in the video. I'm pretty sure the 6A8 won't work until that pin is grounded. Y...RodB — 09:47 PM
Made mistake & did not label connection
You'll have to forgive me, I am not sure what you mean. Can you explain what you are really saying. If anyone does not...georgetownjohn — 08:05 PM
Made mistake & did not label connection
Those are details better left to the ones who know. Maybe you disconnected the wrong end of the wire.RodB — 06:22 PM
Made mistake & did not label connection
Maybe this is starting to make some sense in my hard head. Is this why the wire in question was not in the great Ron Ra...georgetownjohn — 04:34 PM
Made mistake & did not label connection
I was correct with the 6A8 pin connection's, 7 and 8 are connected to ground as well as the tube shield (the broken line...RodB — 02:41 PM
Made mistake & did not label connection
What does the dotted line representing that surrounds the tube in the schematic?georgetownjohn — 02:17 PM
Made mistake & did not label connection
Hello John, I have been there either label got lost or was not labeled ! Sincerely Richardradiorich — 02:15 PM
Made mistake & did not label connection
Sorry, it is a Philco 37-640. Does that help?--Johngeorgetownjohn — 02:14 PM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me