1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Other Radios (Non-Philco)
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Edison Bell Model???
Jayce
Phorum Expert
*****
Posts: 2,026
Threads: 367
Joined: Jun 2010
City: Dover, OH
#6

06-24-2013, 10:33 PM
That tube lineup sounds a bit familiar. I think I have a General radio with a similar line-up and also without a model number. I am pretty sure it is a Simplex-built set.
No matter where you go, there you are.
Find
« Next Oldest | Next Newest »


Messages In This Thread
Edison Bell Model??? - by BrendaAnnD - 06-24-2013, 04:29 PM
RE: Edison-Bell Model??? - by Eliot Ness - 06-24-2013, 07:01 PM
RE: Emerson Bell Model??? - by BrendaAnnD - 06-24-2013, 07:32 PM
RE: Edison Bell Model??? - by BrendaAnnD - 06-24-2013, 07:58 PM
RE: Edison Bell Model??? - by Jayce - 06-24-2013, 10:33 PM
RE: Edison Bell Model??? - by TA Forbes - 06-25-2013, 11:43 AM
RE: Edison Bell Model??? - by BrendaAnnD - 06-25-2013, 04:14 PM
RE: Edison Bell Model??? - by BrendaAnnD - 06-25-2013, 04:19 PM
RE: Edison Bell Model??? - by TA Forbes - 06-26-2013, 09:36 AM
RE: Edison Bell Model??? - by BrendaAnnD - 06-26-2013, 11:31 AM
RE: Edison Bell Model??? - by Alan Douglas - 06-26-2013, 09:08 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Other Radios (Non-Philco)