Philco 34

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Philco 34

marty
Member

Posts: 240
Threads: 27
Joined: Jun 2013
City: Boulder, Colorado

#15

06-28-2013, 08:45 PM

Hi All;
I have started to check things out, And I have fallen in Love with it.. I will have to find another Chassis to modify..
I am going to attempt to Leave it as a Philco 34 and Bring it up as a 34.. I am not going to try and change it to 6.3 volt tubes..
So far the Output transformer seens to be good, it would seem that many of the Resistors may be off..So I will need to take a closer look at both the schematic and the parts placement diagram.. Doing an ohm check on the filaments, it looks like I have one tube that is Bad, the 19, So I will need to get another one..
THANK YOU Marty

Find

« Next Oldest | Next Newest »

Messages In This Thread

Philco 34 - by marty - 06-24-2013, 09:46 PM

RE: Philco 34 - by codefox1 - 06-25-2013, 10:09 AM

RE: Philco 34 - by klondike98 - 06-25-2013, 10:38 AM

RE: Philco 34 - by TA Forbes - 06-25-2013, 11:12 AM

RE: Philco 34 - by marty - 06-25-2013, 01:39 PM

RE: Philco 34 - by 7estatdef - 06-25-2013, 05:34 PM

RE: Philco 34 - by marty - 06-25-2013, 08:18 PM

RE: Philco 34 - by Arran - 06-25-2013, 09:53 PM

RE: Philco 34 - by marty - 06-25-2013, 11:02 PM

RE: Philco 34 - by TA Forbes - 06-26-2013, 09:31 AM

RE: Philco 34 - by marty - 06-26-2013, 11:38 AM

RE: Philco 34 - by morzh - 06-26-2013, 03:12 PM

RE: Philco 34 - by marty - 06-26-2013, 10:23 PM

RE: Philco 34 - by marty - 06-28-2013, 05:40 PM

RE: Philco 34 - by marty - 06-28-2013, 08:45 PM

RE: Philco 34 - by marty - 06-29-2013, 02:50 PM

RE: Philco 34 - by marty - 06-29-2013, 04:39 PM

RE: Philco 34 - by Ron Ramirez - 06-29-2013, 07:13 PM

RE: Philco 34 - by marty - 06-29-2013, 11:14 PM

RE: Philco 34 - by marty - 07-14-2013, 12:25 AM

RE: Philco 34 - by marty - 07-15-2013, 08:23 PM

RE: Philco 34 - by marty - 07-17-2013, 03:51 PM

RE: Philco 34 - by marty - 08-12-2013, 03:57 PM

View a Printable Version

Users browsing this thread: 5 Guest(s)

Recent Posts
trying to identify this wire type
Thanks to all for the feedback. As Arran said, it is probably an older replacement and yes it has a grid cap so I will ...georgetownjohn — 09:32 PM
trying to identify this wire type
It's possible that the red wire, actually a grid cap lead, is a very old replacement, I can't remember seeing a pre 1939...Arran — 09:18 PM
Gilfillan Brothers Car Radio?
Hi everyone, Special thanks to Joe Rossi for tracking down this obscure radio and thanks to others who took up the hun...Antipodal — 08:15 PM
trying to identify this wire type
Here's one source for your wire of many. Take care and BE HEALTHY! Gary P.S. Can't get the right color you need? I ...GarySP — 06:40 PM
trying to identify this wire type
...and modern wire of the appropriate gauges and insulation V-rating (300V minimum, usually shown right on the wire) is ...morzh — 05:47 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
I have a question about this radio, is there anyone that has access to this radio that has an intact unmolested speaker ...captainclock1988 — 04:28 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Well what makes me confuse all of those companies is that all three of those companies (Setchell-Carlson, Stromberg-Carl...captainclock1988 — 04:21 PM
trying to identify this wire type
The red wire is rubber covered wire. The others are cotton braid over rubber often in colors or a tracer, also strand...Chas — 02:43 PM
trying to identify this wire type
Greetings Phorum members, Hope you can help me identify this type of wire in the photo I have attached. I am not sure ...georgetownjohn — 01:53 PM
Philco 60 Squealing
All correct shields must be in place, all tubes correct no subs of any kind. Check any soldered, riveted ground conne...Chas — 01:24 PM

Who's Online

There are currently 5018 online users. [Complete List]
» 1 Member(s) | 5017 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me