Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 34
#19

Hi All;
Ron, Thank You for all Your Knowledge and information.. Yes, that would make sense to me that the Cap was replaced about when the Transformer was replaced..
Since everything else in it looks period correct and as though it hadn't been touched since, repair wise..
The only Exception to that is the Power Cables, which have a modern Gray plastic covered multi - wire cable..
It also, looks like some one took some sand Paper to it to get rid some of the rust on the cans and on some of the chassis.. But, that can all be taken care of with Naval Jelly and Rustoleum primer and Paint..
I have started to take out each Coil and copy down it diameter and number of turns.. So far of the two I have done, one will be a measurement only as its wound like an RF Choke on the inside of the other coil, and I dare not try and remove it nor count its turns as its wound cross-wise for each turn.. The outside coil I can count..
And the IF coils have that leaking wax syndrom, so it should prove interesting getting them out..
And the Screws for the variable capacitor are soldered in to ground and in place.. I also tried all of the Tubes with two weak "D" batteries, all but the bad tube lite up, a 19..
THANK YOU Marty


Messages In This Thread
Philco 34 - by marty - 06-24-2013, 08:46 PM
RE: Philco 34 - by codefox1 - 06-25-2013, 09:09 AM
RE: Philco 34 - by klondike98 - 06-25-2013, 09:38 AM
RE: Philco 34 - by TA Forbes - 06-25-2013, 10:12 AM
RE: Philco 34 - by marty - 06-25-2013, 12:39 PM
RE: Philco 34 - by 7estatdef - 06-25-2013, 04:34 PM
RE: Philco 34 - by marty - 06-25-2013, 07:18 PM
RE: Philco 34 - by Arran - 06-25-2013, 08:53 PM
RE: Philco 34 - by marty - 06-25-2013, 10:02 PM
RE: Philco 34 - by TA Forbes - 06-26-2013, 08:31 AM
RE: Philco 34 - by marty - 06-26-2013, 10:38 AM
RE: Philco 34 - by morzh - 06-26-2013, 02:12 PM
RE: Philco 34 - by marty - 06-26-2013, 09:23 PM
RE: Philco 34 - by marty - 06-28-2013, 04:40 PM
RE: Philco 34 - by marty - 06-28-2013, 07:45 PM
RE: Philco 34 - by marty - 06-29-2013, 01:50 PM
RE: Philco 34 - by marty - 06-29-2013, 03:39 PM
RE: Philco 34 - by Ron Ramirez - 06-29-2013, 06:13 PM
RE: Philco 34 - by marty - 06-29-2013, 10:14 PM
RE: Philco 34 - by marty - 07-13-2013, 11:25 PM
RE: Philco 34 - by marty - 07-15-2013, 07:23 PM
RE: Philco 34 - by marty - 07-17-2013, 02:51 PM
RE: Philco 34 - by marty - 08-12-2013, 02:57 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Cannot Adjust an IF Transformer’s cores
Outstanding work indeed. I wish I could come up with solutions like this.slford310 — 11:16 PM
Cannot Adjust an IF Transformer’s cores
The abilities of our 'Phorum Pholks" never ceases to amaze me! Fantastic fabrication, Joseph! I'm waiting now for...GarySP — 08:27 PM
PT-6 antenna connections
Thanks. I never realized that was a notch noted in the schematic as described. I’ll recheck my wiring.bridkarl — 08:13 PM
Cannot Adjust an IF Transformer’s cores
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM

[-]
Who's Online
There are currently no members online.

>