1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
41-250 oscillator problems
Terry Judkins
Member
***
Posts: 91
Threads: 5
Joined: Oct 2005
City: Atlanta GA
#2

02-05-2008, 05:43 PM
The dual cap marked 21 and 21A should be replaced. It looks like a mica cap but in fact is paper. It has been bad in most of the radios of this design that I have refurbed.

Does the oscillator work with the pushbuttons?
That might give a clue.
Kind regards,
Terry
http://home.comcast.net/~suptjud/
"Life is simpler when you plow around the stump."
Website Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
[No subject] - by Terry Judkins - 02-05-2008, 05:43 PM
[No subject] - by Guest - 02-05-2008, 07:53 PM
[No subject] - by electroubleshooter - 02-05-2008, 09:17 PM
[No subject] - by electroubleshooter - 02-05-2008, 09:18 PM
[No subject] - by Terry Judkins - 02-05-2008, 09:31 PM
[No subject] - by electroubleshooter - 02-05-2008, 11:02 PM
[No subject] - by justlrnin - 02-06-2008, 12:15 AM
[No subject] - by Terry Judkins - 02-06-2008, 11:39 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Zenith H725
David - I think I understand but what units are you discussing (Low of 1.7, high of 3.9)? Budget constraints for Ham ...EdHolland — 01:43 PM
My Philco 37-116 Restore
You're doing great. I wish I could be more involved, but my mind is right now preoccupied with the reason I am here in ...morzh — 12:21 PM
My Philco 37-116 Restore
Hope you guys are still with me. I have moved on to the alignment. I completed the IF alignment which was pretty muc...dconant — 10:47 AM
My Philco 37-116 Restore
Hello MrFixr55, Thank you for taking the time to explain. I measured 50 volts where you say. Today the 370 volts at ...dconant — 12:51 PM
462ron
Oh that sucks. It’s something easily overlooked. Hopefully it’s nothing more than a resistor! Ron462ron — 08:08 AM
Philco 46-480 Electronic Restoration
Just confirmed that you are correct. It’s the function generator. I connected the signal output probe to one of the inpu...jrblasde — 07:52 AM
Philco 46-480 Electronic Restoration
Ouch, you may be right. Yes, it is solid state. It’s the signal output of my oscilloscope. May be time to crack that ...jrblasde — 07:27 AM
462ron
If you didn’t put a DC blocking cap between the signal generator probe and the plate of the 1st IF it’s possible you ble...462ron — 07:07 AM
My Philco 37-116 Restore
Hi DConnant, The reason why C127 is isolated from ground is because sets of this vintage did not have the center tap...MrFixr55 — 01:07 AM
Philco 46-480 Electronic Restoration
The shield is on the 6H6. It was, in fact, a missing jumper to connect the main chassis ground to the RF chassis grou...jrblasde — 10:58 PM

[-]
Who's Online
There are currently 1042 online users. [Complete List]
» 1 Member(s) | 1041 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration